| About |
|---|
| KEPAMID 2315GVS is a glass fiber 15%-reinforced and flame-retardant PA66 grade. It has strong mechanical properties, heat resistance, and flame retardance.(UL94 V-0 type) It is suitable for automotive, electrical & electronics, and industrial parts requiring high stiffness, heat resistance, and flame retardant properties.&& |
| Product Description | |
|---|---|
| Supplier | Korea Engineering |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Flame Characteristics,High Heat Resistance,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.70 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 5.0 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 255 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 235 | ℃ | ISO 75-2/A |
| Melting temperature | 260 | ℃ | ISO 11357-3 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Relative permittivity | |||
| 1 MHz | 3.40 | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.80 mm | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 121 | ISO 2039-2 | |
| tensile strength | 120 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 2.0 | % | ISO 527-2 |
| Bending modulus | 6300 | MPa | ISO 178 |
| bending strength | 170 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | |||
| — | 90 | °C | |
| Dry Air Dryer | 80 | °C | |
| Drying time | |||
| — | 6.0 to 8.0 | hr | |
| Dry Air Dryer | 4.0 to 6.0 | hr | |
| Recommended maximum moisture content | 0.050 | % | |
| Hopper temperature | 60 to 80 | °C | |
| Barrel rear temperature | 280 | °C | |
| Barrel middle temperature | 285 | °C | |
| Barrel front temperature | 290 | °C | |
| Nozzle temperature | 300 | °C | |
| Mold temperature | 70 to 90 | °C | |
| Back pressure | 0.490 to 0.981 | MPa | |
| Screw speed | 80 to 120 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |