| About |
|---|
| Kingfa PBT-RG151 is a Polybutylene Terephthalate (PBT) material filled with 15% glass fiber. It is available in Asia Pacific or North America for injection molding. Important attributes of Kingfa PBT-RG151 are: Flame Rated Flame Retardant Heat Resistant High Strength Typical applications include: Electrical/Electronic Applications Appliances Lighting Applications&& |
| Product Description | |
|---|---|
| Supplier | Kingfa |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Electrical Properties,Low to No Fogging,Flame Characteristics,High Heat Resistance,V-0 |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.55 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| TD：23℃ | 1.1 | % | ASTM D955 |
| MD：23℃ | 0.50 | % | ASTM D955 |
| Water absorption rate | |||
| 23℃，24hr | 0.070 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，3.2mm | 70 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 6.4 mm | 205 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 215 | ℃ | ASTM D648 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.30 mm | V-0 | UL 94 | |
| 0.75 mm | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 95.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 3.4 | % | ASTM D638 |
| Bending modulus | 5600 | MPa | ASTM D790 |
| bending strength | 150 | MPa | ASTM D790 |
| Rockwell hardness | |||
| R-level | 120 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 to 140 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Barrel rear temperature | 220 to 240 | °C | |
| Barrel middle temperature | 235 to 255 | °C | |
| Barrel front temperature | 240 to 265 | °C | |
| Processing (melt) temperature | 240 to 260 | °C | |
| Mold temperature | 50 to 70 | °C | |
| Injection speed | Moderate-Fast | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |