| About |
|---|
| Kingfa ULTRON-C090 is an Acetal (POM) Homopolymer material. It is available in Asia Pacific or North America for injection molding. Important attributes of Kingfa ULTRON-C090 are: Flame Rated Creep Resistant Fatigue Resistant High Strength Medium Viscosity Typical applications include: Automotive Electrical/Electronic Applications Engineering/Industrial Parts Industrial Applications&& |
| Product Description | |
|---|---|
| Supplier | Kingfa |
| Generic | Paraformaldehyde |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good flexibility,Fatigue resistance |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.41 | g/cm³ | ISO 1183 |
| Shrinkage rate | 1.8 to 2.2 | % | ISO 2577 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.20 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 7.0 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 155 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 100 | ℃ | ISO 75-2/A |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 2 mm in oil | 21 | kV/mm | IEC 60243-1 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 118 | ISO 2039-2 | |
| tensile strength | 62.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| fracture | 35 | % | ISO 527-2/50 |
| Bending modulus | 2500 | MPa | ISO 178 |
| bending strength | 80.0 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 to 100 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Barrel rear temperature | 170 to 190 | °C | |
| Barrel middle temperature | 175 to 200 | °C | |
| Barrel front temperature | 180 to 210 | °C | |
| Processing (melt) temperature | 180 to 210 | °C | |
| Mold temperature | 50 to 90 | °C | |
| Injection speed | 中等偏快 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |