| About |
|---|
| High Density Polyethylene Copolymer HMW Extrusion-Blow Molding Applications Bottles for home use chemical liquid substances (bleache) and industrial chemicals (lubricants) up to 10 litters. Bottles containing liquids for personal use (shampoo). Bottles for pharmaceutical products. Characteristics The KPOL® resin meets the requirements of section 177.1520, paragraph C, from chapter 21 denominated “Olefin Polymers” from the Code of Federal Regulations of the FDA, to be utilized with direct food contact.&& |
| Product Description | |
|---|---|
| Generic | HDPE |
| Material Status | Commercial: Active |
| Features | Food contact compliance,Inoxidizability,High molecular weight,Copolymer,High density |
| Availabilitys | North America,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.951 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | ASTM D1238 | ||
| 190℃，2.16kg | 0.17 | g/10min | ASTM D1238 |
| 190℃，21.6kg | 13 | g/10min | ASTM D1238 |
| ESCR(Environmental Stress Cracking Resistance) | ASTM D1693B | ||
| 60 ℃, 10% wetting agent, F50 | > 500 | hr | ASTM D1693B |
| 50 ℃, 1.90 mm, 100% wetting agent, F50 | 58.0 | hr | ASTM D1693B |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 270 | J/m | ASTM D256-A |
| Tensile impact strength | 242 | kJ/m² | ASTM D1822 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 75.0 | ℃ | ASTM D648 |
| Embrittlement temperature | < -75.0 | ℃ | ASTM D746A |
| Vicat Softening Temp | 125 | ℃ | ASTM D1525 7 |
| Melting temperature | 129 | ℃ | DSC |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore D, 1 second, 23 ℃ | 68 | ASTM D2240 | |
| tensile strength | |||
| yield | 27.6 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 600 | % | ASTM D638 |
| Bending modulus | |||
| Tangent, 3.20 mm | 1380 | MPa | ASTM D790 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 16 oz cylindrical bottle (approximated mass of 20 g) filled up to 33% of its capacity |
| 3. Grooved Specimen |
| 4. Type IV, 2.0 in/min |
| 5. 0.51 in/min |
| 6. F50; 25 lbfXin |
| 7. Rate A (50°C/h), Loading 1 (10 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |