KUBE PIR 21821

About
Transmissive Plastic Injection Molding Granulates For fresnel lenses and windows of PIR motion detectors, thermal imaging cameras and non-contact thermometers Features: The best material for fresnel lenses Specially suited for thin parts High transmission in the 7 to 14 µm central passive infrared (PIR) band Choice of colors and MFI RoHS and TSCA conform Excellent visible light absorption available for low false alarm rate / VDS conformity Special colors available on request According to KUBE’s experience, these materials exhibit no substantial loss of specification over 10 years 21821: for applications where the material is not exposed to light over long periods&&

About

Transmissive Plastic Injection Molding Granulates For fresnel lenses and windows of PIR motion detectors, thermal imaging cameras and non-contact thermometers Features: The best material for fresnel lenses Specially suited for thin parts High transmission in the 7 to 14 µm central passive infrared (PIR) band Choice of colors and MFI RoHS and TSCA conform Excellent visible light absorption available for low false alarm rate / VDS conformity Special colors available on request According to KUBE’s experience, these materials exhibit no substantial loss of specification over 10 years 21821: for applications where the material is not exposed to light over long periods&&

Product Description
Generic	HDPE
Material Status	Commercial: Active
Features	Flame Characteristics
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.951 to 0.960	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	17	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Tensile Modulus	825	MPa	ISO 527-2
Tensile Strength			ISO 527-2
Yield yld	23.1	MPa	ISO 527-2
Broken BRK	11.6	MPa	ISO 527-2
Tensile Strain			ISO 527-2
Yield yld	3.0	%	ISO 527-2
Broken BRK	51	%	ISO 527-2

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179
-30℃	3.8	kJ/m²	ISO 179
23℃	3.7	kJ/m²	ISO 179
Charpy Unnotch Impact strength			ISO 179
-30℃	97	kJ/m²	ISO 179
23℃	97	kJ/m²	ISO 179

Process Conditions
Injection Molding	Nominal value	Unit	Test method
Drying Temperature	< 70	°C
Drying Time	2.0	hr
Hopper Temperature	50 to 70	°C
Rear Temperature Zone 1	170 to 220	°C
Middle Temperature Zone 2	200 to 220	°C
Front Temperature Zone 3	210 to 220	°C
Nozzle temperature	220 to 230	°C
Melt Temperature	130	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.