| About |
|---|
| ABS713是耐热ABS树脂，用于电镀，具有高刚性和高冲击力。ABS713推荐用于汽车内饰，如散热器格栅，支柱装饰，手柄等。 |
| Product Description | |
|---|---|
| Supplier | KumhoSunny |
| Generic | ABS |
| Material Status | Commercial: Active |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| tensile strength | 39 | MPa | ISO 527 |
| Tensile strain | |||
| yield | 84 | % | ISO 527 |
| bending strength | |||
| yield | 60 | MPa | ISO 178 |
| Bending modulus | 2187 | MPa | ISO 178 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 83 | ℃ | ISO 75 |
| 0.45 MPa | 94 | ℃ | ISO 75 |
| Vicat Softening Temp | 102 | ℃ | ISO 306 |
| Linear coefficient of thermal expansion | |||
| MD | 7.71×10-5 | 1/℃ | ISO 11359 |
| TD | 7.56×10-5 | 1/℃ | ISO 11359 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melt Flow Rate | |||
| 220℃，10.0kg | 14 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | |||
| MD | 0.40~0.70 | % | ISO 294 |
| Density | 1.05 | g/cm³ | ISO 1183 |
| Poisson’s ratio | 0.394 | ISO 527 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1E+15 | ohms | IEC 60093 |
| Volume resistivity | 1.00E+15 | ohms·cm | IEC 60093 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 26 | kJ/m² | ISO 180 |
| -30℃ | 12 | kJ/m² | ISO 180 |
| 23℃ | NB | kJ/m² | ISO 180ISO 180 |
| -30℃ | NB | kJ/m² | ISO 180 |
| Charpy Notched Impact Strength | |||
| 23℃ | 28 | kJ/m² | ISO 179 |
| -30℃ | 15 | kJ/m² | ISO 179 |
| 23℃ | NB | kJ/m² | ISO 179 |
| -30℃ | NB | kJ/m² | ISO 179 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| drying temperature | 80~85 | ℃ | |
| Drying time | 3~4 | hrs | |
| Maximum moisture content | 0.05 | /% | |
| Roller temperature – top | 230~250 | ℃ | |
| Roller temperature – middle | 220~240 | ℃ | |
| Roller temperature – bottom | 200~220 | ℃ | |
| Nozzle temperature | 235~255 | ℃ | |
| Mold temperature | 50~80 | ℃ | |
| Melt Temperature | 235~255 | ℃ | |
| Back pressure | 1~5 | Mpa | |
| Screw speed | 30~70 | rpm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |