| About |
|---|
| Product Description | |
|---|---|
| Generic | Polycarbonate |
| Material Status | Commercial: Negative |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.25 | g/cm³ | ASTM D792 |
| Melt index | |||
| 300℃，1.2kg | 15 | g/10min | ISO 1133 |
| Forming shrinkage rate | 0.3 – 0.6 | % | ISO 294-4 |
| Water absorption rate | 0.35 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 50 mm/min | 54 | MPa | ISO 527-2 |
| elongation at break | |||
| 50 mm/min | 90 | % | ISO 527-2 |
| Tensile modulus | |||
| 5 mm/min | 1850 | MPa | ISO 527-2 |
| bending strength | |||
| 2 mm/min | 82 | MPa | ISO 178 |
| Bending modulus | |||
| 2 mm/min | 2100 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 850 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | NB | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 116 | ℃ | ISO 75-2 |
| Vicat Softening Temp | 137 | ℃ | ISO 306 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 1 Hz | 4.75 | ASTM D150-11 | |
| 100 Hz | 4.32 | ASTM D150-11 | |
| 5GHz | 2.85 | ICP-TM-650.2.5.5.5 | |
| Dissipation factor | |||
| 1 Hz | 10.2E-3 | ASTM D150-11 | |
| 100 Hz | 1.7E-3 | ASTM D150-11 | |
| 5GHz | 4.8E-2 | ICP-TM-650.2.5.5.5 | |
| Volume resistivity | 1.0E+16 | ohm·cm | IEC 60093 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| drying temperature | 90 – 110 | ℃ | |
| Drying time | 4 – 6 | hrs | |
| Maximum moisture content | 0.05 | % | |
| Melting temperature | 285 – 300 | ℃ | |
| Hopper temperature | 50 – 80 | ℃ | |
| A period of temperature | 275 – 280 | ℃ | |
| Second stage temperature | 280 – 285 | ℃ | |
| Three stage temperature | 285 – 290 | ℃ | |
| Nozzle temperature | 290 – 295 | ℃ | |
| Mold temperature | 60 – 80 | ℃ | |
| Back pressure | 0.1 – 0.5 | MPa | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |