| About |
|---|
| Product Description | |
|---|---|
| Supplier | Asahi Kasei |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | ISO 1183 | |
| water content | |||
| balance | 2.5 | % | |
| Shrinkage rate | |||
| MD：3.0 mm | 1.3 | % | |
| TD：3.0 mm | 2.0 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | |||
| yield | |||
| Tensile strain | |||
| dry | 82 | MPa | ISO 527 |
| wet | 52 | MPa | ISO 527 |
| fracture | |||
| yield | |||
| Stretching coefficient | |||
| dry | 3 | GPa | ISO 527 |
| dry | 4 | % | ISO 527 |
| wet | 1.2 | GPa | ISO 527 |
| wet | 24 | % | ISO 527 |
| Flexural strength | |||
| dry | – | MPa | ISO 527 |
| dry | 113 | MPa | ISO 178 |
| wet | – | MPa | ISO 527 |
| wet | 42 | MPa | ISO 178 |
| dry | – | % | ISO 527 |
| Flexural resistance coefficient | |||
| wet | >100 | % | ISO 527 |
| dry | 2.7 | GPa | ISO 178 |
| wet | 1.1 | GPa | ISO 178 |
| Rockwell hardness | |||
| R-grade, dry | 120 | ISO 2039 | |
| M-grade, dry | 80 | ISO 2039 | |
| R-grade, wet | 108 | ISO 2039 | |
| M-grade, wet | 55 | ISO 2039 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear coefficient of thermal expansion | |||
| MD | 8 | 10-5/K | ASTM D696 |
| Hot deformation temperature | |||
| 1.8 MPa | 70 | ℃ | ISO 75 |
| 0.45 MPa | 190 | ℃ | ISO 75 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Comparison of arc resistance track index | 575 | IEC 60112 | |
| Dielectric strength | 20 | KV/mm | ASTM D149 |
| Surface resistance coefficient | 10^13 | Ω· | ASTM D 257 |
| Volumetric resistance coefficient | 10^14 | Ω·cm | ASTM D 257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| UL | V2 | UL 94 | |
| Hot filament ignition | |||
| 3mm | 960 | ℃ | IEC 60695 -2-1 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 39 | J/m | ASTM D256 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |