| About |
|---|
| LEXAN™ HP4NR是一种无定形的聚碳酸酯。具有生物相容性和蒸汽杀菌等级,不包含脱模.中等流动性，良好的延展性，韧性和清晰度。经注射成型加工，用于医疗器械和制药应用。符合ISO10993 / USPVI 等级 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Biocompatible |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Rockwell hardness | |||
| M-level | 70 | ASTM D785 | |
| R-level | 118 | ASTM D785 | |
| Taber wear and tear | |||
| CS-17，1kg | 10 | mg/1000cy | ASTM D1044 |
| tensile strength | |||
| Yield, 50 mm/min | 61 | MPa | ISO 527 |
| Fracture, 50 mm/min | 73 | MPa | ISO 527 |
| Tensile strain | |||
| Yield, 50 mm/min | 6 | % | ISO 527 |
| Fracture, 50 mm/min | 128 | % | ISO 527 |
| Tensile modulus | |||
| 1 mm/min | 2390 | MPa | ISO 527 |
| bending strength | |||
| Yield, 2 mm/min | 93 | MPa | ISO 178 |
| Bending modulus | 2250 | MPa | ISO 178 |
| 2 mm/mim | 2250 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 810 | J/m | ASTM D256 |
| -30℃ | 220 | J/m | ASTM D256 |
| Tensile impact | |||
| S-shaped | 59 | N.m | ASTM D 1822 |
| Drop hammer impact | |||
| D 3029，23℃ | 173 | N.m | ASTM D3029 |
| Total energy of instrument impact | |||
| 23℃ | 90 | N.m | ASTM D 3763 |
| Notched impact strength of cantilever beam | |||
| 23℃ | 3260 | J/m | ASTM D 4812 |
| 23℃，80*10*3 | NB | kJ/m² | ISO 180/1U |
| -30℃，80*10*3 | NB | kJ/m² | ISO 180/1U |
| Impact strength of cantilever beam notch | |||
| 23℃，80*10*3 | 70 | kJ/m² | ISO 180-1A |
| -30℃，80*10*3 | 10 | kJ/m² | ISO 180-1A |
| Charpy Notched Impact Strength | |||
| 80*10*3 | |||
| 80*10*3 | |||
| 23℃ | 75 | kJ/m² | ISO 179/1eA |
| -30℃ | 15 | kJ/m² | ISO 179/1eA |
| 23℃ | NB | kJ/m² | ISO 179/1eU |
| -30℃ | NB | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 154 | ℃ | ASTM D1525 |
| Hot deformation temperature | |||
| 1.8 MPa, 100 mm span | 127 | ℃ | ISO 75/Ae |
| Unannealed, 6.4 mm | |||
| 1.8 MPa, unannealed, 3.2 mm | 126 | ℃ | ASTM D648 |
| 0.45 MPa | 137 | ℃ | ASTM D 648 |
| 1.8MPa | 132 | ℃ | ASTM D 648 |
| Linear expansion coefficient, -40 ℃ to 40 ℃ | |||
| flow | 7.8E-05 | 1/℃ | ASTM E 831 |
| transverse | 7.6E-05 | 1/℃ | ASTM E 831 |
| Linear coefficient of thermal expansion | |||
| -40 ℃ to 95 ℃, flowing | 6.84E-05 | 1/℃ | ASTM E 831 |
| specific heat | 1.25 | J/g-℃ | ASTM C 351 |
| Thermal conductivity coefficient | 0.19 | W/m/℃ | ASTM C 177 |
| Linear expansion coefficient, -40 ℃ to 40 ℃ | |||
| flow | 7.8E-05 | 1/℃ | ISO 11359-2 |
| transverse | 7.6E-05 | 1/℃ | ISO 11359-2 |
| Ball pressure test | |||
| 125℃±2℃ | PASSES | IEC 60695-10-2 | |
| Vicat Softening Temp | |||
| B50 | 143 | ℃ | ISO 306 |
| B120 | 145 | ℃ | ISO 306 |
| Relative temperature index | |||
| Electrical performance | 130 | ℃ | UL 746B |
| Impact mechanical performance | 130 | ℃ | UL 746B |
| Non mechanical impact performance | 130 | ℃ | UL 746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.2 | ASTM D792 | |
| Specific volume | 0.83 | cm³/g | ASTM D 792 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.26 | % | ISO 62 |
| 23℃，50% RH | 0.1 | % | ISO 62 |
| 24hr | 0.15 | % | ASTM D570 |
| Equilibrium, 23 ℃ | 0.35 | % | ASTM D570 |
| Equilibrium, 100 ℃ | 0.58 | % | ASTM D570 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5 – 0.7 | % | Internal Method |
| Melt Flow Rate | |||
| 300℃，1.20kg | 10.5 | g/10min | ASTM D1238 |
| Density | 1.19 | ISO 1183 | |
| Melt Volume Rate | |||
| 300℃，2.16 kg | 10 | cm³/10min | ISO 1133 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 2.54 mm | 88 | % | ASTM D1003 |
| Haze | |||
| 2.54 mm | 1 | % | ASTM D1003 |
| Refractive index | 1.586 | ASTM D542 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | >1.E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.2 mm in air | 14.9 | kV/mm | ASTM D149 |
| Relative permittivity | |||
| 50-60 Hz | 3.17 | ASTM D150 | |
| 1 MHz | 2.96 | ASTM D150 | |
| Dissipation factor | |||
| 50-60 Hz | 0.0009 | ASTM D150 | |
| 1 MHz | 0.01 | ASTM D150 | |
| Hot wire ignition {PLC | 2 | PLC Code | UL 746A |
| High voltage arc marking rate {PLC | 2 | PLC Code | UL 746A |
| High current arc ignition (surface {PLC) | 1 | PLC Code | UL 746A |
| Compared to the leakage tracing index | 2 | PLC Code | UL 746A |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 94HB flame rating assessment | 1.47 | mm | UL 94 |
| Extreme oxygen index | |||
| LOI | 25 | % | ASTM D2863 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| Drying temperature | 120 | ||
| Drying time | 3 – 4 | hrs | |
| Drying time (cumulative) | 48 | hrs | |
| Maximum water content | 0.02 | % | |
| Melt temperature | 295 – 315 | °C | |
| Nozzle temperature | 290 – 310 | °C | |
| Front Section Zone 3 Temperature | 295 – 315 | °C | |
| Temperature in Zone 2 of the middle section | 280 – 305 | °C | |
| Temperature in Zone 1 of the rear section | 270 – 295 | °C | |
| Mold temperature | 70 – 95 | °C | |
| Back pressure | 0.3 – 0.7 | MPa | |
| Screw speed | 40 – 70 | rpm | |
| Shoot to cylinder size | 40 – 60 | % | |
| Depth of exhaust groove | 0.025 – 0.076 | mm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |