| About |
|---|
| 标准流动性、透明、高纯度聚碳酸酯共聚物树脂，氧渗透率降低，水汽传质率降低。用于医疗设备和药物应用。卫生保健管理的改变，生物兼容(iso10993或USP类VI)，符合食品接触级。 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Food contact compliance |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Rockwell hardness | |||
| Level L | 108 | ASTM D785 | |
| M-level | 93 | ASTM D785 | |
| Taber wear and tear | |||
| CS-17，1kg | 10 | ||
| mg/1000cy | ASTM D 1044 | ||
| mg/1000cy | SABIC Method | ||
| tensile strength | |||
| Yield, 50 mm/min | 80 | MPa | ISO 527 |
| Fracture, 50 mm/min | 60 | MPa | ISO 527 |
| Tensile strain | |||
| Yield, 50 mm/min | 7 | % | ISO 527 |
| Fracture, 50 mm/min | 40 | % | ISO 527 |
| Tensile modulus | |||
| 1 mm/min | 2450 | MPa | ISO 527 |
| bending strength | |||
| Yield, 2 mm/min | 108 | MPa | ISO 178 |
| Bending modulus | |||
| 2 mm/mim | 2450 | MPa | ISO 178 |
| Ball hardness | |||
| H358/30 | 128 | MPa | ISO 2039-1 |
| Pencil hardness test | |||
| 1kgf | H | ASTM D 3363 | |
| Erikson scratch depth | |||
| 6N | 14 | micrometer | SABIC Metho |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 30 | J/m | ASTM D256 |
| -30℃ | 30 | J/m | ASTM D256 |
| Total energy of instrument impact | |||
| 23℃ | 305 | cm-kgf | ASTM D 3763 |
| Notched impact strength of cantilever beam | |||
| 23℃ | NB | J/m | ASTM D 4812 |
| 23℃，80*10*3 | NB | kJ/m² | ISO 180/1U |
| -30℃，80*10*3 | 45 | kJ/m² | ISO 180/1U |
| 23℃，80*10*4 | NB | kJ/m² | ISO 180/1U |
| -30℃，80*10*4 | 47 | kJ/m² | ISO 180/1U |
| Impact strength of cantilever beam notch | |||
| 23℃，80*10*3 | 50 | kJ/m² | ISO 180-1A |
| -30℃，80*10*3 | 40 | kJ/m² | ISO 180-1A |
| 80*10*4 -30℃ | 30 | kJ/m² | ISO 180-1A |
| 80*10*3 sp=62mm，23℃ | 30 | kJ/m² | ISO 179/1eA |
| 80*10*3 sp=62mm，-30℃ | 30 | kJ/m² | ISO 179/1eA |
| 80*10*4 sp=62mm，23℃ | 30 | kJ/m² | ISO 179/1eA |
| 80*10*4 sp=62mm，-30℃ | NB | kJ/m² | ISO 179/1eA |
| Charpy Notched Impact Strength | |||
| 80 * 10 * 3, 62mm span | |||
| 23 ℃, 80 * 10 * 3, 62mm span | NB | kJ/m² | ISO 179/1eU |
| -30 ℃, 80 * 10 * 3, 62mm span | 47 | kJ/m² | ISO 179/1eU |
| 23 ℃, 80 * 10 * 4, 62mm span | NB | kJ/m² | ISO 179/1eU |
| -30 ℃, 80 * 10 * 4, 62mm span | 47 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 139 | ℃ | ASTM D1525 |
| Hot deformation temperature | |||
| 0.45 MPa, 100 mm span | 131 | ℃ | ISO 75/Be |
| 1.8 MPa, 100 mm span | 118 | ℃ | ISO 75/Ae |
| Unannealed, 6.4 mm | |||
| Unannealed, 3.2 mm | |||
| 0.45 MPa | 133 | ℃ | ASTM D 648 |
| 1.8MPa | 119 | ℃ | ASTM D 648 |
| 0.45 MPa | 133 | ℃ | ASTM D 648 |
| 1.8MPa | 119 | ℃ | ASTM D 648 |
| Linear expansion coefficient, -40 ℃ to 40 ℃ | |||
| flow | 7.E-05 | 1/℃ | ASTM E 831 |
| transverse | 7.E-05 | 1/℃ | ASTM E 831 |
| specific heat | 1.4 | J/g-℃ | ASTM C 351 |
| Thermal conductivity coefficient | |||
| 0.2 | W/m/℃ | ASTM C177 | |
| 0.2 | W/m/℃ | ISO 8302 | |
| Linear expansion coefficient, from 23 ℃ to 80 ℃ | |||
| flow | 7.E-05 | 1/℃ | ISO 11359-2 |
| transverse | 7.E-05 | 1/℃ | ISO 11359-2 |
| Ball pressure test | |||
| 125℃±2℃ | PASSES | IEC 60695-10-2 | |
| Maximum approximation value | 140 | ℃ | IEC 60695-10-2 |
| Vicat Softening Temp | |||
| B50 | 138 | ℃ | ISO 306 |
| B120 | 140 | ℃ | ISO 306 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.2 | ASTM D792 | |
| Specific volume | 0.85 | cm³/g | ASTM D 792 |
| Water absorption rate | |||
| 24hr，50% RH | 0.04 | % | ASTM D570 |
| Saturation, 23 ℃ | 0.27 | % | ISO 62 |
| 23℃，50% RH | 0.13 | % | ISO 62 |
| 24hr | 0.08 | % | ASTM D570 |
| Equilibrium, 23 ℃ | 0.28 | % | ASTM D570 |
| Equilibrium, 100 ℃ | 0.13 | % | ASTM D570 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5 – 0.8 | % | Internal Method |
| Melt Flow Rate | |||
| 300℃，1.20kg | 14.5 | g/10min | ASTM D1238 |
| Density | 1.17 | ISO 1183 | |
| Melt Volume Rate | |||
| 300℃，2.16 kg | 13 | cm³/10min | ISO 1133 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 2.54 mm | 88 | % | ASTM D1003 |
| Haze | |||
| 2.54 mm | <0.8 | % | ASTM D1003 |
| Refractive index | 1.586 | ASTM D542 | |
| Refractive index | 1.586 | ISO 489 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | >1.E+17 | ohms·cm | ASTM D257 |
| Relative permittivity | |||
| 50-60 Hz | 2.9 | ASTM D150 | |
| 1 MHz | 2.8 | ASTM D150 | |
| Compared to the leakage tracing index | 2 | PLC Code | UL 746A |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 3 – 4 | hrs | |
| Maximum water content | 0.02 | % | |
| Melt temperature | 295 – 315 | °C | |
| Nozzle temperature | 290 – 310 | °C | |
| Front Section Zone 3 Temperature | 295 – 315 | °C | |
| Temperature in Zone 2 of the middle section | 280 – 305 | °C | |
| Temperature in Zone 1 of the rear section | 260 – 280 | °C | |
| Mold temperature | 80 – 115 | °C | |
| Hopper temperature | 70 – 95 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |