| About |
|---|
| 7.0 MFR。 改善阻燃性。 紫外线稳定，适用于户外和照明。 内部脱模。 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Flame Characteristics,Internal mold release |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.19 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 300℃，1.20kg | 7.0 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5~0.7 | % | |
| Water absorption rate | |||
| 24hr | 0.15 | % | ASTM D570 |
| 0.35 | % | ASTM D570 | |
| Equilibrium, 100 ℃ | 0.58 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 70 | ASTM D785 | |
| R-level | 118 | ASTM D785 | |
| tensile strength | |||
| yield | 62.1 | MPa | ASTM D638 |
| fracture | 65.5 | MPa | ASTM D638 |
| Tensile strain | |||
| yield | 7.0 | % | ASTM D638 |
| fracture | 110 | % | ASTM D638 |
| Bending modulus | 2340 | MPa | ASTM D790 |
| bending strength | |||
| yield | 93.1 | MPa | ASTM D790 |
| Taber abraser | 10 | mg | ASTM D1044 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| 750 | J/m | ASTM D256 | |
| 3200 | J/m | ASTM D4812 | |
| Drop hammer impact | 169 | J | ASTM D3029 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | > 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.2 mm | 15 | KV/mm | ASTM D149 |
| Dielectric constant | |||
| 50 Hz | 3.17 | ASTM D150 | |
| 60 Hz | 3.17 | ASTM D150 | |
| 1 MHz | 2.96 | ASTM D150 | |
| Dissipation factor | |||
| 50 Hz | 9.0E-4 | ASTM D150 | |
| 60 Hz | 9.0E-4 | ASTM D150 | |
| 1 MHz | 0.01 | ASTM D150 | |
| Compared to the leakage tracing index | PLC 3 | UL 746 | |
| PLC 1 | UL 746 | ||
| PLC 3 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.75-1.65 mm | V-2 | UL 94 | |
| Glowing wire flammability index | |||
| 0.75 mm | 750 | ℃ | IEC 60695-2-12 |
| 1.5 mm | 850 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | |||
| 0.75 mm | 875 | ℃ | IEC 60695-2-13 |
| 1.5 mm | 850 | ℃ | IEC 60695-2-13 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| drying temperature | 121 | °C | |
| Drying time | 3~4 | hrs | |
| Accumulated drying time | 48 | hrs | |
| Maximum moisture content | 0.02 | % | |
| Shoot to cylinder size | 40~60 | °C | |
| Temperature at the rear of the barrel | 288~310 | °C | |
| Temperature in the middle of the barrel | 299~321 | °C | |
| Front temperature of material barrel | 310~332 | °C | |
| Nozzle temperature | 304~327 | °C | |
| Melt Temperature | 310~332 | °C | |
| Mold temperature | 82.2~116 | °C | |
| Back pressure | 0.345~0.689 | MPa | |
| Screw speed | 40~70 | rpm | |
| Depth of exhaust groove | 0.025~0.076 | mm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |