LIM™ 6040 - SOLIAO

About
LIM 6040 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive Performance Materials masterbatch colors. Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 1500C (3020F) to 2050C (4000F) Excellent release from metal molds Potential Applications The combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls&&

About

LIM 6040 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive Performance Materials masterbatch colors. Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 1500C (3020F) to 2050C (4000F) Excellent release from metal molds Potential Applications The combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls&&

Product Description
Supplier	Momentive
Generic	硅橡胶,LSR
Material Status	Commercial: Active
Features	Good Clarity,Good stripping performance,Good Tensile Strength,Good tear strength,Fast Cure,HB
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Liquid injection molding

Technical Data
elastic body	Nominal value	Unit	Test method
Basho’s elasticity
—	54	%
—	58	%

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	HB		UL 94

THERMAL	Nominal value	Unit	Test method
Thermosetting components
Component A	按重量计算的混合比: 1.0
Component B	按重量计算的混合比: 1.0

Uncured Properties	Nominal value	Unit
colour
—	Clear/Transparent
—	Clear/Transparent
Density
—	1.12	g/cm³
—	1.12	g/cm³

Cured Properties	Nominal value	Unit
Shore hardness
Shaw’s A	40
Shaw’s A	42
Tensile modulus
100% secant	1.06	MPa
100% secant	1.50	MPa
tensile strength
—	8.30	MPa
—	9.70	MPa
Tensile strain
fracture	600	%
fracture	650	%
Compression deformation
177℃，22 hr	25	%
177℃，22 hr	40	%
tear strength
Die B	40.4	kN/m
Die B	40.4	kN/m
Electrical strength	18	kV/mm
Relative permittivity
1 kHz	3.00
Volume resistivity
—	6.4E+14	ohms·cm
Dissipation factor
1 kHz	1.0E-4

Notes
1. Typical properties: these are not to be construed as specifications.
2. Postbaked 1 hr @ 204°C (400°F)
3. As Molded 30 sec @ 177°C (350°F)
4. Part B
5. Part A
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.