LITEN ZB 29 - SOLIAO

About
LITEN ZB 29 is a linear polyethylene, copolymer, intended for blow moulding and extrusion. It exhibits resistance to tensoactive substances, impact strength and good processability. It is suitable for manufacture of pipes for non-pressure applications, sheets, profiles, bottles, canisters, etc. This grades is delivered in the form of stabilized powder. LITEN ZB 29 meets the hygienic regulations concerning contact with food of the European Union (Commission Directive), Germany (BfR) and USA (FDA). The product is not classified as a dangerous preparation according to Directive 1999/45/EC.&&

About

LITEN ZB 29 is a linear polyethylene, copolymer, intended for blow moulding and extrusion. It exhibits resistance to tensoactive substances, impact strength and good processability. It is suitable for manufacture of pipes for non-pressure applications, sheets, profiles, bottles, canisters, etc. This grades is delivered in the form of stabilized powder. LITEN ZB 29 meets the hygienic regulations concerning contact with food of the European Union (Commission Directive), Germany (BfR) and USA (FDA). The product is not classified as a dangerous preparation according to Directive 1999/45/EC.&&

Product Description
Generic	PE copolymerization
Material Status	Commercial: Active
Features	Excellent Processability,High impact resistance,Food contact compliance,Copolymer,Solvent resistance
Availabilitys	Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.952	g/cm³	ISO 1183
Melt Flow Rate			ISO 1133
190℃，2.16kg	0.20	g/10min	ISO 1133
190℃，21.6kg	24	g/10min	ISO 1133
190℃，5.0kg	1.2	g/10min	ISO 1133
ESCR(Environmental Stress Cracking Resistance)
F50	250	hr	ASTM D1693
Melt flow ratio
21，6/2，16	100

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179
-30℃	5.0	kJ/m²	ISO 179
23℃	11	kJ/m²	ISO 179

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	45.0	℃	ISO 75-2/A
Vicat Softening Temp	124	℃	ISO 306
Melting temperature	130	℃	ISO 11357-3

Supplementary information	Nominal value	Unit	Test method
Blow Molding Melt Temperature	180 to 220	℃
Blow Molding Mold Temperature	20 to 30	℃

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	60		ISO 868
tensile strength
yield	25.0	MPa	ISO 527-2
Tensile strain
yield	10	%	ISO 527-2
Bending modulus	1100	MPa	ISO 178

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.