| About |
|---|
| Thermally conductive, electrically conductive mineral filled PA6 compound&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Conductive,Thermal conductivity,HB |
| Availabilitys | Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.61 | g/cm³ | ASTM D792，ISO 1183 |
| Shrinkage rate | ASTM D955 | ||
| MD：24 hrs | 0.15 | % | |
| TD：24 hrs | 0.17 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 10800 | MPa | ASTM D638 |
| — | 16000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 54.0 | MPa | ASTM D638 |
| fracture | 75.0 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| fracture | 1.0 | % | ASTM D638 |
| fracture | 0.90 | % | ISO 527-2/5 |
| Bending modulus | |||
| 50 mm span | 12400 | MPa | ASTM D790 |
| — | 14000 | MPa | ISO 178 |
| bending strength | |||
| — | 90.0 | MPa | ISO 178 |
| Fracture, 50 mm span | 78.0 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 26 | J/m | ASTM D256 |
| 23℃ | 3.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 150 | J/m | ASTM D4812 |
| 23℃ | 8.0 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 186 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 200 | ℃ | ISO 75-2/Af |
| Ball pressure test | |||
| 165℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 1.6E-5 | 1/℃ | ASTM E831 |
| MD：-30~80℃ | 1.4E-5 | 1/℃ | ISO 11359-2 |
| MD：23~80℃ | 1.6E-5 | 1/℃ | ISO 11359-2 |
| TD：-40~40℃ | 3.6E-5 | 1/℃ | ASTM E831 |
| TD：-30~80℃ | 4.0E-5 | 1/℃ | ISO 11359-2 |
| TD：23~80℃ | 4.8E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | |||
| — | 3.5 | W/m/K | ASTM E1461 |
| — | 15 | W/m/K | ASTM E1461 |
| — | 1.5 | W/m/K | ISO 22007-2 |
| — | 18 | W/m/K | ISO 22007-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 3.0E+5 | ohms | ASTM D257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.00 mm | HB | UL 94 | |
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 1.0 mm | 850 650 | ℃ | |
| 1.6 mm | 960 | ℃ | |
| Igniting temperature of the hot wire | |||
| 1 mm | 825 | ℃ | IEC 60695-2-13 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80.0 to 90.0 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Barrel rear temperature | 260 to 290 | °C | |
| Barrel middle temperature | 270 to 300 | °C | |
| Barrel front temperature | 270 to 300 | °C | |
| Nozzle temperature | 270 to 300 | °C | |
| Processing (melt) temperature | 270 to 300 | °C | |
| Mold temperature | 80.0 to 100 | °C | |
| Back pressure | 3.00 to 9.00 | MPa | |
| Screw speed | 30 to 150 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. Type I, 0.20 in/min |
| 4. 0.051 in/min |
| 5. 0.079 in/min |
| 6. at Break |
| 7. 80*10*4 mm |
| 8. through-plane, 10*10*3 mm sample |
| 9. in-plane, 25*0.4 mm disc |
| 10. through-plane, 60*60*3 mm plaque |
| 11. in-plane, 60*60*3 mm plaque |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |