| About |
|---|
| Thermally conductive, mineral filled PA6 compliant with ECO protocols, non-brominated, non chlorinated&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Halogen free,Thermal conductivity,ECO,V-0 |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.68 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD | 0.70 | % | Internal Method |
| MD：24 hrs | 0.55 | % | ASTM D955 |
| TD：24 hrs | 0.65 | % | ASTM D955 |
| TD：24 hrs | 0.65 | % | ISO 294-4 |
| MD：24 hrs | 0.55 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 0.23 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 10400 | MPa | ASTM D638 |
| — | 13000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 68.0 | MPa | ASTM D638 |
| fracture | 75.0 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| fracture | 1.2 | % | ASTM D638 |
| fracture | 1.1 | % | ISO 527-2/5 |
| Bending modulus | |||
| 50 mm span | 11800 | MPa | ASTM D790 |
| — | 12000 | MPa | ISO 178 |
| bending strength | |||
| — | 105 | MPa | ISO 178 |
| Fracture, 50 mm span | 119 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 15 | J/m | ASTM D256 |
| 23℃ | 3.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 150 | J/m | ASTM D4812 |
| 23℃ | 9.0 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 203 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 64 mm span | 203 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed, 3.2 mm | 137 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 160 | ℃ | ISO 75-2/Af |
| Ball pressure test | |||
| 165℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 3.3E-5 | 1/℃ | ASTM E831 |
| MD：-30~80℃ | 3.9E-5 | 1/℃ | ISO 11359-2 |
| TD：-40~40℃ | 4.4E-5 | 1/℃ | ASTM E831 |
| TD：-30~80℃ | 5.5E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | ISO 22007-2 | ||
| — | 1.2 | W/m/K | |
| — | 5.5 | W/m/K |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 4.0E+14 | ohms | ASTM D257 |
| Dielectric strength | |||
| 1.6 mm in oil | 7.2 | kV/mm | ASTM D149 |
| Compared to the leakage tracing index | PLC 0 | UL 746 | |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| High Arc Burning Index (HAI) | PLC 0 | UL 746 | |
| Hot wire ignition | |||
| HWI | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.80 mm | V-0 | UL 94 | |
| Glowing wire flammability index | |||
| 0.80 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 0.8 mm | 750 | ℃ | |
| 1.6 mm | 775 | ℃ | |
| 3 mm | 800 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80.0 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.15 to 0.25 | % | |
| Barrel rear temperature | 260 to 275 | °C | |
| Barrel middle temperature | 270 to 290 | °C | |
| Barrel front temperature | 270 to 290 | °C | |
| Processing (melt) temperature | 270 to 295 | °C | |
| Mold temperature | 85.0 to 100 | °C | |
| Back pressure | 0.200 to 0.300 | MPa | |
| Screw speed | 20 to 60 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar |
| 3. 0.20 in/min |
| 4. Type I, 0.20 in/min |
| 5. 0.051 in/min |
| 6. 0.079 in/min |
| 7. at Yield |
| 8. 80*10*4 mm |
| 9. through-plane, 60*60*3 mm plaque |
| 10. in-plane, 60*60*3 mm plaque |
| 11. Surface |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |