| About |
|---|
| LNP™ LUBRICOMP™ DFL36 compound LNP* LUBRICOMP* DFL36 is a compound based on Polycarbonate resin containing 30% Glass Fiber, 15% PTFE. Added feature of this material is: Wear Resistant. Also known as: LNP* LUBRICOMP* Compound DFL-4036 Product reorder name: DFL36&&LNP™ LUBRICOMP™ DFL36 compound LNP LUBRICOMP DFL-4036 is a compound based on Polycarbonate resin containing Glass Fiber, PTFE. Also known as: LNP* LUBRICOMP* Compound DFL-4036 Product reorder name: DFL36&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Lubricating,Good wear resistance |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.54 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| TD：24 hrs | 0.50 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9580 | MPa | ASTM D638 |
| Tensile modulus | 9080 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 118 | MPa | ISO 527-2 |
| fracture | 123 | MPa | ASTM D638 |
| yield | 118 | MPa | ISO 527-2 |
| yield | 123 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 2.7 | % | ISO 527-2 |
| fracture | 2.8 | % | ASTM D638 |
| yield | 2.6 | % | ASTM D638 |
| yield | 2.6 | % | ISO 527-2 |
| Bending modulus | 8620 | MPa | ASTM D790 |
| Bending modulus | 8340 | MPa | ISO 178 |
| bending strength | 186 | MPa | ASTM D790 |
| bending strength | 185 | MPa | ISO 178 |
| friction coefficient | ASTM D3702 Modified | ||
| dynamic | 0.46 | ASTM D3702 Modified | |
| static state | 0.41 | ASTM D3702 Modified | |
| Wear factor | |||
| Washer | 22.0 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 920 | J/m | ASTM D4812 |
| 23℃ | 19 | kJ/m² | ISO 180-1A |
| 23℃ | 200 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23℃ | 55 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 144 | ℃ | ASTM D648 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Barrel rear temperature | 293 to 304 | °C | |
| Barrel middle temperature | 310 to 321 | °C | |
| Barrel front temperature | 321 to 332 | °C | |
| Processing (melt) temperature | 304 to 327 | °C | |
| Mold temperature | 82 to 110 | °C | |
| Back pressure | 0.172 to 0.344 | MPa | |
| Screw speed | 30 to 60 | rpm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |