| About |
|---|
| LNP STAT-KON DX07323 is a compound based on polycarbonate resin containing conductive fillers. Added features of this compound includes: ESD safe and excellent low-temperature impact performance, intended for compliance to ATEX.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Features | Electrostatic discharge protection,low-temperature impact resistance,V-1 |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.26 | g/cm³ | ASTM D792, ISO 1183 |
| Melt Flow Rate | |||
| 300℃，10.0kg | 55 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 300℃，10 kg | 50.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.50 | % | Internal Method |
| MD：24 hrs | 0.40 to 0.70 | % | ASTM D955 |
| TD | 0.50 | % | Internal Method |
| TD：24 hrs | 0.40 to 0.70 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 2400 | MPa | ASTM D638 |
| — | 2400 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 45.0 | MPa | ASTM D638 |
| yield | 55.0 | MPa | ISO 527-2/5 |
| fracture | 55.0 | MPa | ASTM D638 |
| fracture | 44.0 | MPa | ISO 527-2/5 |
| Tensile strain | ASTM D638, ISO 527-2/5 | ||
| yield | 5.0 | % | |
| fracture | 9.0 | % | |
| Bending modulus | |||
| — | 2200 | MPa | ASTM D790 |
| — | 2400 | MPa | ISO 178 |
| bending strength | |||
| — | 84.0 | MPa | ASTM D790 |
| — | 88.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| -40℃ | 100 | J/m | ASTM D256 |
| 23℃ | 180 | J/m | ASTM D256 |
| -40℃ | 10 | kJ/m² | ISO 180-1A |
| 23℃ | 16 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| -40℃ | 1500 | J/m | ASTM D4812 |
| 23℃ | 1600 | J/m | ASTM D4812 |
| -40℃ | 100 | kJ/m² | ISO 180/1U |
| 23℃ | 130 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 125 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 124 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | ASTM E831, ISO 11359-2 | ||
| MD：-40~40℃ | 5.0E-5 | 1/℃ | |
| TD：-40~40℃ | 5.0E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+6 to 1.0E+10 | ohms | ASTM D257 |
| Volume resistivity | 1.0E+6 to 1.0E+10 | ohms·cm | ASTM D257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 2.50 mm | V-1 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 48 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.20 in/min |
| 3. 0.079 in/min |
| 4. Type 1A |
| 5. at Break |
| 6. 80*10*4 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |