| About |
|---|
| LNP* Thermocomp* DX13354 compound is a 30% glass fiber reinforced, impact modified PC resin based LDS material solution with stable plating and RF performance. Good surface aesthetics and wide processing window makes it a good candidate for internal and external parts for Laser Direct Structuring applications.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Good surface appearance,High impact resistance |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.47 | g/cm³ | ASTM D792 |
| Melt Flow Rate | ASTM D1238 | ||
| 280℃，2.16kg | 10 | g/10min | |
| 280℃，5.0kg | 27 | g/10min | |
| 300℃，1.20kg | 16 | g/10min | |
| Melt Volume Rate | |||
| 300℃，1.2 kg | 13.0 | cm³/10min | ASTM D1238 |
| Shrinkage rate | Internal Method | ||
| MD：3.2 mm | 0.050 to 0.10 | % | |
| TD：3.2 mm | 0.20 to 0.40 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 8760 | MPa | ASTM D638 |
| — | 8840 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 120 | MPa | ASTM D638 |
| fracture | 120 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| fracture | 2.4 | % | ASTM D638 |
| fracture | 2.4 | % | ISO 527-2/50 |
| Bending modulus | |||
| — | 8020 | MPa | ASTM D790 |
| — | 8450 | MPa | ISO 178 |
| bending strength | |||
| — | 170 | MPa | ASTM D790 |
| — | 180 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 14 | kJ/m² | ISO 179/2C |
| Charpy Unnotch Impact strength | |||
| 23℃ | 50 | kJ/m² | ISO 179/2U |
| Impact strength of cantilever beam notch | |||
| 23℃ | 150 | J/m | ASTM D256 |
| 23℃ | 14 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 700 | J/m | ASTM D4812 |
| 23℃ | 40 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 126 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 64 mm span | 127 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed, 3.2 mm | 122 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 124 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 2.1E-5 | 1/℃ | ASTM E831，ISO 11359-2 |
| TD：-40~40℃ | 6.9E-5 | 1/℃ | ASTM E831 |
| TD：-40~40℃ | 7.1E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | Internal Method | ||
| 1.10 GHz | 3.52 | ||
| 1.9 GHz | 3.44 | ||
| 5.00 GHz | 3.51 | ||
| Dissipation factor | Internal Method | ||
| 1.1 GHz | 0.014 | ||
| 1.9 GHz | 0.013 | ||
| 5 GHz | 0.012 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Barrel rear temperature | 270 to 295 | °C | |
| Barrel middle temperature | 270 to 295 | °C | |
| Barrel front temperature | 270 to 295 | °C | |
| Nozzle temperature | 270 to 295 | °C | |
| Processing (melt) temperature | 270 to 295 | °C | |
| Mold temperature | 100 to 120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.20 in/min |
| 3. Type I, 0.20 in/min |
| 4. Type 1A |
| 5. 80*10*4 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |