| About |
|---|
| Description Flame Retardance Application IT/OA(Housing)&& |
| Product Description | |
|---|---|
| Supplier | LG Chemical |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,V-0 |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 1.25 | g/cm³ | ASTM D792 |
| — | 1.24 | g/cm³ | ISO 1183-3 |
| Melt Flow Rate | |||
| 250℃，2.16kg | 4.0 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 260℃，5 kg | 26.2 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.20 to 0.40 | % | ASTM D955 |
| Water absorption rate | |||
| saturated | 0.11 | % | ISO 62-3 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA 3 | ||
| -30℃ | 4.90 | kJ/m² | ISO 179/1eA 3 |
| 23℃ | 6.80 | kJ/m² | ISO 179/1eA 3 |
| Charpy impact strength | ISO 179/1eU 3 | ||
| -30℃ | 29.5 | kJ/m² | ISO 179/1eU 3 |
| 23℃ | 35.4 | kJ/m² | ISO 179/1eU 3 |
| Impact strength of cantilever beam notch | |||
| 23℃，3.2mm | 69 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa | 125 | ℃ | ISO 75-2 3 |
| 1.8 MPa, unannealed, 6.4 mm | 113 | ℃ | ASTM D648 |
| 1.8 MPa | 109 | ℃ | ISO 75-2 3 |
| Glass transition temperature | 140 | ℃ | ISO 11357-2 3 |
| Vicat Softening Temp | |||
| B50 | 117 | ℃ | ISO 306 3 |
| Linear coefficient of thermal expansion | ISO 11359-2 3 | ||
| MD | 4.5E-5 | 1/℃ | ISO 11359-2 3 |
| TD | 7.8E-5 | 1/℃ | ISO 11359-2 3 |
| Relative temperature index | 60.0 | ℃ | UL 746 |
| Electrical performance | 60.0 | ℃ | UL 746 |
| Impact mechanical performance | 60.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 3 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 3 |
| Electrical strength | 29 | kV/mm | IEC 60243-1 3 |
| Relative permittivity | |||
| 1 MHz | 3.10 | IEC 60250 3 | |
| Dissipation factor | |||
| 1 MHz | 0.010 | IEC 60250 3 | |
| Compared to the leakage tracing index | 200 | IEC 60112 3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.70 mm | V-0 | UL 94 | |
| 3.00 mm | V-0 | UL 94 | |
| Flame retardant level | |||
| 1.70 mm | V-0 | ISO 1210 3 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 115 | ASTM D785 | |
| Tensile modulus | 4000 | MPa | ISO 527-2 3 |
| tensile strength | |||
| Yield, 3.20 mm | 65.7 | MPa | ASTM D638 |
| fracture | 77.0 | MPa | ISO 527-2 3 |
| Tensile strain | |||
| Fracture, 3.20 mm | 7.0 | % | ASTM D638 |
| fracture | 3.4 | % | ISO 527-2 3 |
| Bending modulus | |||
| 3.20 mm | 3920 | MPa | ASTM D790 |
| bending strength | |||
| 3.20 mm | 108 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 75 to 85 | °C | |
| Drying time | 3.0 to 5.0 | hr | |
| Recommended maximum moisture content | < 0.020 | % | |
| Barrel rear temperature | 220 to 240 | °C | |
| Barrel middle temperature | 235 to 255 | °C | |
| Barrel front temperature | 250 to 265 | °C | |
| Nozzle temperature | 250 to 265 | °C | |
| Processing (melt) temperature | 235 to 265 | °C | |
| Mold temperature | 50 to 80 | °C | |
| Back pressure | 0.0196 to 0.0588 | MPa | |
| Screw speed | 40 to 70 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 3. 0.20 in/min |
| 4. 0.051 in/min |
| 5. 18 °F/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |