| About |
|---|
| Luranyl® HT 190 is a Polyphenylene Ether + PA 66 (PPE+Nylon 66) material. It is available in Europe. Important attributes of Luranyl® HT 190 are: Flame Rated Heat Resistant&& |
| Product Description | |
|---|---|
| Generic | PPO(PPE)+PA 66 |
| Material Status | Commercial: Active |
| Features | High Heat Resistance,HB |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.05 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 280℃，5 kg | 20.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| 23℃，3.2 mm | 0.90 to 1.1 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | < 0.40 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 2050 | MPa | ISO 527-1-2 |
| tensile strength | |||
| Yield, 23 ℃ | 50.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| Fracture, 23 ℃ | 90 | % | ISO 527-2/50 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 12 | kJ/m² | |
| 23℃ | 45 | kJ/m² | |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | 无断裂 | ||
| 23℃ | 无断裂 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 120 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| B50 | 180 | ℃ | ISO 306 |
| Linear coefficient of thermal expansion | |||
| MD：23~80℃ | 9.5E-5 | 1/℃ | ISO 11359-2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80.0 to 100 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.050 | % | |
| Processing (melt) temperature | 270 to 300 | °C | |
| Mold temperature | 80.0 to 120 | °C | |
| Injection speed | 中等 | ||
| Screw speed | 12 to 18 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |