| About |
|---|
| Lustran® 248FC resin is a high-gloss, medium-impact grade of ABS (acrylonitrile butadiene styrene). FEATURES Healthcare certifications High Gloss Medium impact Compliant with both food and medical regulations APPLICATIONS Components of intravenous (IV)systems Surgical instruments Diagnostic test kits&& |
| Product Description | |
|---|---|
| Supplier | INEOS |
| Generic | ABS |
| Material Status | Commercial: Active |
| Features | Good surface appearance,Food contact compliance |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.06 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 0.40-0.60 | % | ASTM D995 |
| Melt Flow Rate | |||
| 230℃，3.80kg | 5.0 | g/10min | ASTM D1238 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | 100 | ℃ | ASTM D648 |
| Hot deformation temperature | 86.0 | ℃ | ASTM D648 |
| Hot deformation temperature | 93.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| Hot deformation temperature | 96.0 | ℃ | ASTM D648 |
| 80.0 | ℃ | ASTM D1525 |
| Other performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 245-265 | ℃ | |
| Dew point | <=-29.0 | ℃ | |
| Hot deformation temperature | 102 | ℃ | |
| Clamping pressure | 30.8-61.6 | MPa | |
| buffer | <=0.635 | cm |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 224 | J/m | ASTM D256 |
| -40℃ | 48.0 | J/m | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 112 | R 级 | ASTM D785 |
| tensile strength | |||
| Yield, 23 ℃ | 47.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | |||
| Tensile modulus | |||
| 23℃ | 2600 | MPa | ASTM D638 |
| bending strength | |||
| Yield, 23 ℃ | 74.0 | MPa | ASTM D790 |
| Bending modulus | |||
| 23℃ | 2700 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 71.0 -77.0 | °C | |
| Drying time | 4 | Hr | |
| Water content | <=0.10 | % | |
| Injection temperature | |||
| Rear barrel temperature | 235-250 | °C | |
| Central temperature of the barrel | 240 -255 | °C | |
| Barrel front temperature | 245-260 | °C | |
| Mold temperature | 45.0-65.0 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |