| About |
|---|
| Lustran® 451 is a easy flowing, medium impact injection molding resin designed with a unique balance of impact, heat resistance, flow and gloss. FEATURES Medium impact strength Medium flow Unique balance of impact, heat resistance, flow and gloss UL 94 HB APPLICATIONS Major appliance&& |
| Product Description | |
|---|---|
| Supplier | INEOS |
| Generic | ABS |
| Material Status | Commercial: Active |
| Features | Moderate liquidity,HB |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.06 | g/cm³ | ASTM D792 |
| Melt Flow Rate | ASTM D1238 | ||
| 200℃，5.0kg | 1.8 | g/10min | ASTM D1238 |
| 230℃，3.80kg | 4.4 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.40 to 0.60 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -18℃ | 69 | J/m | ASTM D256 |
| 23℃ | 180 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 102 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 80.6 | ℃ | ASTM D648 |
| Vicat Softening Temp | 96.1 | ℃ | ASTM D1525 2 |
| Linear coefficient of thermal expansion | |||
| MD | 8.3E-5 | 1/℃ | ASTM D696 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2620 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 23 ℃ | 42.7 | MPa | ASTM D638 |
| Bending modulus | 2590 | MPa | ASTM D790 |
| bending strength | |||
| 5% strain | 74.5 | MPa | ASTM D790 |
| Rockwell hardness | |||
| R-level | 107 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 79 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Mold temperature | 43 to 66 | °C | |
| Screw length to diameter ratio | 20.0:1.0 | ||
| Screw compression ratio | 2.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Rate B (120°C/h), Loading 1 (10 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |