| About |
|---|
| LUVOCOM® 1800-9333/WT is a Polyethylene Terephthalate (PET) material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding. Important attributes of LUVOCOM® 1800-9333/WT are: Conductive Good Stiffness Heat Stabilizer Typical applications include: Automotive Business/Office Goods Electrical/Electronic Applications Engineering/Industrial Parts Fabrics/Fibers&& |
| Product Description | |
|---|---|
| Supplier | Lehmann |
| Generic | PET |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Thermal conductivity,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.60 | g/cm³ | ISO 1183 |
| Shrinkage rate | 0.40 to 0.80 | % | DIN 16901 |
| Water absorption rate | |||
| 23℃，24hr | < 0.30 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9500 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 54.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| yield | 1.1 | % | ISO 527-2 |
| Bending modulus | 8500 | MPa | ISO 178 |
| bending strength | 85.0 | MPa | ISO 178 |
| Bending strain | 1.8 | % | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 22 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Continuous use temperature | 100 | ℃ | UL 746B |
| Maximum operating temperature | |||
| short-term | 180 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 3.0E-5 | 1/℃ | DIN 53752 |
| Thermal conductivity coefficient | 7.0 | W/m/K |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+13 | ohms | IEC 60093 |
| insulation resistance | > 1.0E+13 | ohms | IEC 60167 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | |||
| Hot air dryer, A | 120 | °C | |
| Hot air dryer, B | 80 | °C | |
| Drying time | |||
| Hot air dryer, A | 2.0 to 5.0 | hr | |
| Hot air dryer, B | 6.0 to 8.0 | hr | |
| Barrel rear temperature | 285 to 295 | °C | |
| Barrel middle temperature | 270 to 280 | °C | |
| Barrel front temperature | 265 to 275 | °C | |
| Nozzle temperature | 265 to 275 | °C | |
| Processing (melt) temperature | 280 | °C | |
| Mold temperature | 60 to 120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Hot-Disk, 60x60x3 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |