| About |
|---|
| (PC+PET) blend, unreinforced; UV-stabilized; impact modified; high flow; injection molding grade; good impact strength; dimensional stability and chemical resistance. Suitable for some food contact applications (contact Covestro for more information).&& |
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | PC+PET |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,High impact resistance,Good Dimensional Stability,High liquidity,Food contact compliance,Solvent resistance,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 270℃，5 kg | 20.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | ISO 2577 | ||
| TD | 0.60 to 0.80 | % | ISO 2577 |
| MD | 0.60 to 0.80 | % | ISO 2577 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.50 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.20 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 2400 | MPa | ISO 527-1-2 |
| tensile strength | |||
| Fracture, 23 ℃ | 64.0 | MPa | ISO 527-2/50 |
| Yield, 23 ℃ | 59.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| Yield, 23 ℃ | 5.5 | % | ISO 527-2/50 |
| Nominal tensile fracture strain | |||
| 23℃ | 100 | % | ISO 527-2/50 |
| Bending modulus | |||
| 23℃ | 2350 | MPa | ISO 178 |
| bending strength | ISO 178 | ||
| 23℃ | 88.0 | MPa | ISO 178 |
| 3.50% strain, 23 ℃ | 71.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ISO 7391 | ||
| -30℃ | 10 | kJ/m² | ISO 7391 |
| 23℃ | 60 | kJ/m² | ISO 7391 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 109 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 131 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| B120 | 142 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | |||
| TD：23~55℃ | 8.0E-5 | 1/℃ | ISO 11359-2 |
| MD：23~55℃ | 7.0E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | |||
| 23℃ | 0.20 | W/m/K | ISO 8302 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+16 | ohms | IEC 60093 |
| Volume resistivity | |||
| 23℃ | 1.0E+16 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 23 ℃，1 mm | 34 | kV/mm | IEC 60243-1 |
| Relative permittivity | IEC 60250 | ||
| 23℃，100 Hz | 3.20 | IEC 60250 | |
| 23℃，1 MHz | 3.10 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 23℃，100 Hz | 1.3E-3 | IEC 60250 | |
| 23℃，1 MHz | 0.014 | IEC 60250 | |
| Compared to the leakage tracing index | |||
| Solution A | 375 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | HB | UL 94 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 600 bar |
| 3. 0.079 in/min |
| 4. Based on ISO 180-A, 3 mm |
| 5. Cross-flow |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |