| About |
|---|
| The compound can be an ideal solution for applications like coax cables, electronic cables, communication cables, low voltage power cables, instrumentation and control cables in harsh environments.&& |
| Product Description | |
|---|---|
| Generic | 热塑性聚酯 |
| Material Status | Commercial: Active |
| Features | Low smoke,Crosslinked radiation,Halogen free,Flame Characteristics,High Heat Resistance,Grease resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.45 | g/cm³ | ISO 1183/A |
| Melt Flow Rate | |||
| 190℃，2.16kg | 12 | g/10min | ISO 1133 |
| Water absorption rate | |||
| 70℃，10days | 5.00 | mg/cm² | IEC 811-1-3 |
| 23℃，24hr | 0.50 | % | IEC 811-1-3 |
| PH value | 5.6 | IEC 60754-2 | |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | 49.0 | kN/m | ASTM D624 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 120℃，240 hr | 6.0 | % | IEC 811-1-2 |
| Changes in tensile stress during fracture in air | |||
| 120℃，240 hr | -12 | % | IEC 811-1-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| thermosetting | IEC 540 | ||
| Elongation under load | 20 | % | IEC 60540 |
| Residual elongation | 3.0 | % | IEC 60540 |
| Temperature index | 300 | ℃ | ASTM D2863 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+11 | ohms·cm | IEC 60167 |
| Dielectric constant | |||
| 50 Hz | 3.90 | IEC 60250 | |
| Conductivity | 0.900 | µS/mm | EN 50267-2-2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Extreme oxygen index | 38 | % | ASTM D2863 |
| Halogen Content | < 0.100 | % | IEC 754-1 |
| toxicity | 1.00 | NES 713 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 90 | ISO 7619 | |
| tensile strength | IEC 811-1-1 | ||
| — | > 8.00 | MPa | IEC 811-1-1 |
| — | 16.0 | MPa | IEC 811-1-1 |
| Tensile strain | |||
| fracture | > 250 | % | IEC 811-1-1 |
| fracture | 180 | % | IEC 811-1-1 |
| Fracture, -40 ℃ | 25 | % | IEC 811-1-4 |
| Fracture, -30 ℃ | 45 | % | IEC 811-1-4 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Barrel 1 zone temperature | 150 to 160 | °C | |
| Barrel 2 zone temperature | 160 to 170 | °C | |
| Barrel 3 zone temperature | 165 to 175 | °C | |
| Barrel 4 zone temperature | 170 to 180 | °C | |
| Barrel 5 zone temperature | 170 to 180 | °C | |
| Connector temperature | 170 to 180 | °C | |
| Head temperature | 170 to 180 | °C | |
| Nozzle temperature | 170 to 180 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. After crosslinking |
| 3. Before crosslinking |
| 4. at 200°C/15min/0.2 MPa |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |