Mediprene® 500502M

About
Mediprene 500502M: Thermoplastic Elastomer Material Type: TPS-SEBS Hardness: 50 Shore A (4mm) Service Temperature Range: -50 — +100°C (unstressed material) Colour: Transparent, but can be available in any colour. Presentation: Free flowing pellets that can be processed without predrying, when stored under normal conditions. Weather Resistance: Good Chemical Resistance: Good (excluding organic solvents, aromatic- and vegetable oils) Recyclability: 100% recyclable Special Features: The material is based on medically approved raw materials.&&

About

Mediprene 500502M: Thermoplastic Elastomer Material Type: TPS-SEBS Hardness: 50 Shore A (4mm) Service Temperature Range: -50 — +100°C (unstressed material) Colour: Transparent, but can be available in any colour. Presentation: Free flowing pellets that can be processed without predrying, when stored under normal conditions. Weather Resistance: Good Chemical Resistance: Good (excluding organic solvents, aromatic- and vegetable oils) Recyclability: 100% recyclable Special Features: The material is based on medically approved raw materials.&&

Product Description
Generic	SEBS
Material Status	Commercial: Active
Features	Weather resistance is good,Excellent Processability,Renewable resources,Solvent resistance
Availabilitys	Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.890	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	12	g/10min	ASTM D1238

elastic body	Nominal value	Unit	Test method
tear strength	28.0	kN/m	ASTM D624

THERMAL	Nominal value	Unit	Test method
Operating temperature	-50 to 100	℃

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shore A, 4.00 mm	50		ASTM D2240
Tensile modulus			ASTM D638
100% secant	1.40	MPa	ASTM D638
300% secant	2.50	MPa	ASTM D638
tensile strength	6.00	MPa	ASTM D638
Tensile strain
fracture	650	%	ASTM D638

Process Conditions
injection	Nominal value	Unit	Test method
Extrusion	Nominal value	Unit	Test method
Barrel rear temperature	150 to 210	°C
Barrel middle temperature	150 to 210	°C
Barrel front temperature	150 to 210	°C
Mold temperature	20 to 40	°C
Barrel 1 zone temperature	140 to 180	°C
Barrel 2 zone temperature	140 to 180	°C
Barrel 3 zone temperature	140 to 180	°C
Barrel 4 zone temperature	140 to 180	°C
Barrel 5 zone temperature	140 to 180	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.