| About |
|---|
| Organically and inorganically filled Melamine moulding compound Excellent surface hardness, good mechanical strength, good electrical properties Primary application(s): Mountings for household appliances, car ash-trays This product meets the allowed upper limits for heavy metals and PCAs and also conforms to the requirements of the EU directives 2002/95 (RoHS), 2002/96 (WEEE) and 2006/122 (PFOS)&& |
| Product Description | |
|---|---|
| Supplier | RASCHIG |
| Generic | MF |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Electrical Properties,Good Hardness,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 to 1.70 | g/cm³ | ISO 1183 |
| Apparent density | 0.55 to 0.75 | g/cm³ | ISO 60 |
| Shrinkage rate | ISO 2577 | ||
| MD | 0.80 to 1.3 | % | ISO 2577 |
| MD | 0.50 to 1.0 | % | ISO 2577 |
| Water absorption rate | |||
| 23℃，24hr | < 2.0 | % | ISO 62 |
| Post contraction | 1.0 to 1.5 | % | ISO 2577 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | ISO 527-2 | ||
| Compression Molding | 5000 to 8000 | MPa | ISO 527-2 |
| injection molding | 5000 to 8000 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| Compression Molding | 40.0 to 65.0 | MPa | ISO 527-2 |
| injection molding | 50.0 to 90.0 | MPa | ISO 527-2 |
| Bending modulus | ISO 178 | ||
| Compression Molding | 8000 to 9000 | MPa | ISO 178 |
| injection molding | 8000 to 9000 | MPa | ISO 178 |
| bending strength | ISO 178 | ||
| Compression Molding | 90.0 to 120 | MPa | ISO 178 |
| injection molding | 100 to 130 | MPa | ISO 178 |
| compressive strength | 200 to 250 | MPa | ISO 604 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| Compression Molding | 1.4 to 2.0 | kJ/m² | ISO 179/1eA |
| injection molding | 1.5 to 2.0 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| Compression Molding | 6.0 to 9.0 | kJ/m² | ISO 179/1eU |
| injection molding | 8.0 to 14 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 155 to 180 | ℃ | ISO 75-2/A |
| 8.0 MPa, unannealed | 110 to 130 | ℃ | ISO 75-2/C |
| Linear coefficient of thermal expansion | |||
| MD：50~100℃ | 1.5E-5 to 3.5E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | 0.40 to 0.50 | W/m/K | ASTM E1461 |
| Maximum operating temperature | IEC 60216 | ||
| <50 h | 160 | ℃ | IEC 60216 |
| 20，000 h | 135 | ℃ | IEC 60216 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+10 to 1.0E+11 | ohms | IEC 60093 |
| Volume resistivity | 1.0E+11 to 1.0E+12 | ohms·cm | IEC 60093 |
| Dielectric strength | 15 to 20 | kV/mm | IEC 60243-1 |
| Relative permittivity | IEC 60250 | ||
| 100 Hz | 11.0 16.0 | IEC 60250 | |
| 1 MHz | 7.00 9.00 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 100 Hz | 0.30 to 0.50 | IEC 60250 | |
| 1 MHz | 0.030 to 0.050 | IEC 60250 | |
| Arc resistance | PLC 5 | ASTM D495 | |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.5 mm，Tested by RASCHIG | V-0 | UL 94 | |
| Glowing wire flammability index | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | 900 | ℃ | IEC 60695-2-13 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Compression molding pressure | > 20.0 | MPa | |
| Compression molding temperature | 160 to 180 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel middle temperature | 70 to 90 | °C | |
| Barrel front temperature | 90 to 100 | °C | |
| Processing (melt) temperature | 100 to 115 | °C | |
| Mold temperature | 160 to 180 | °C | |
| Back pressure | 0.800 to 1.20 | MPa | |
| Screw speed | 80 to 120 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Compression Molded |
| 3. Injection Molded |
| 4. 168 h / 110°C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |