| About |
|---|
| Miramid® S3CF is a Polyamide 66 (Nylon 66) material. It is available in Europe for injection molding. Important attributes of Miramid® S3CF are: Flame Rated Chemical Resistant Flame Retardant Good Mold Release Mold Release Agent Typical application of Miramid® S3CF: Electrical/Electronic Applications&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good liquidity,Good stripping performance,Flame Characteristics,Grease resistance,Solvent resistance,Fuel resistance |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.17 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| 23℃，50% RH | 2.30 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 23℃ | 80 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 10 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 3500 | MPa | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 3200 | MPa | ISO 178 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 70 | ℃ | ISO 75-2/A |
| Melting temperature | 260 | ℃ | ISO 11357-3 |
| Vicat Softening Temp |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+13 | Ω.cm | IEC 60093 |
| Dielectric constant | |||
| 23℃ | 3.40 | 1 MHz | IEC 60250 |
| Dissipation factor | |||
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | V-0 | UL 94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 50 | kJ/m² | ISO 179/1eU |
| -30℃ | 45 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 4.0 | kJ/m² | ISO 179/1eA |
| -30℃ | 3.0 | kJ/m² | ISO 179/1eA |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Injection temperature | |||
| Mold temperature | 70-80 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |