Moplen EP300R - SOLIAO

About
Moplen EP300R Moplen EP300R is the polypropylene block copolymer manufactured by PMC under the license of BASELL using the Spheripol process. Moplen EP300R is a block copolymer selected by customers for use in injection molding of washing machine tub, thin-walled packaging, parts of electrical appliances, housewares. Moplen EP300R resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.&&Moplen EP300R Moplen EP300R is a polypropylene impact copolymer with optimized balance of stiffness and toughness, and high impact strength even at low temperature. Typical customer applications are injection molding of washing machine tubs, electrical appliance parts, housewares and thin walled packaging.&&

About

Moplen EP300R Moplen EP300R is the polypropylene block copolymer manufactured by PMC under the license of BASELL using the Spheripol process. Moplen EP300R is a block copolymer selected by customers for use in injection molding of washing machine tub, thin-walled packaging, parts of electrical appliances, housewares. Moplen EP300R resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.&&Moplen EP300R Moplen EP300R is a polypropylene impact copolymer with optimized balance of stiffness and toughness, and high impact strength even at low temperature. Typical customer applications are injection molding of washing machine tubs, electrical appliance parts, housewares and thin walled packaging.&&

Product Description
Supplier	LyondellBasell
Generic	PP copolymer
Material Status	Commercial: Active
Features	Good Rigidity,Low warping,Excellent Processability,Good flexibility,High impact resistance,Food contact compliance,Block Copolymer,low-temperature impact resistance,Impact copolymer
Availabilitys	Africa & Middle East ,Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.900	g/cm³	ASTM D1505
Melt Flow Rate
230℃，2.16kg	30	g/10min	ASTM D1238

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch			ASTM D256
-20 ℃, injection molding	49	J/m	ASTM D256
23 ℃, injection molding	130	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	150	℃	ASTM D1525

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	85		ASTM D785
tensile strength
Yield, injection molding	23.5	MPa	ASTM D638
Tensile strain
Yield, injection molding	5.0	%	ASTM D638
Bending modulus
injection molding	1030	MPa	ASTM D790

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.