Moplen EP500N - SOLIAO

About
Moplen EP500N Moplen EP500N is the polypropylene block copolymer manufactured by PMC under the license of BASELL using the Spheripol process. Moplen EP500N is a block copolymer selected by customers and used in for injection molding of containers, parts of electrical appliances, crates and pails. Moplen EP500N resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.&&Moplen EP500N Moplen EP500N is a polypropylene impact copolymer with optimized balance of stiffness and toughness, low warpage, and high impact at low temperature. Typical customer applications are injection molding of crates and pails, electrical appliances parts and general housewares.&&

About

Moplen EP500N Moplen EP500N is the polypropylene block copolymer manufactured by PMC under the license of BASELL using the Spheripol process. Moplen EP500N is a block copolymer selected by customers and used in for injection molding of containers, parts of electrical appliances, crates and pails. Moplen EP500N resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.&&Moplen EP500N Moplen EP500N is a polypropylene impact copolymer with optimized balance of stiffness and toughness, low warpage, and high impact at low temperature. Typical customer applications are injection molding of crates and pails, electrical appliances parts and general housewares.&&

Product Description
Supplier	LyondellBasell
Generic	PP copolymer
Material Status	Commercial: Active
Features	Good Rigidity,Low warping,Excellent Processability,High impact resistance,Food contact compliance,Block Copolymer,Ultra high toughness,low-temperature impact resistance,Impact copolymer
Availabilitys	Africa & Middle East ,Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.900	g/cm³	ISO 1183 , ASTM D1505
Melt Flow Rate
230℃，2.16kg	12	g/10min	ASTM D1238，ISO 1133

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179/1eA
-20℃	3.0	kJ/m²	ISO 179/1eA
0℃	3.5	kJ/m²	ISO 179/1eA
23℃	5.0	kJ/m²	ISO 179/1eA
Charpy Unnotch Impact strength			ISO 179/1eU
-20℃	无断裂		ISO 179/1eU
0℃	无断裂		ISO 179/1eU
23℃	无断裂		ISO 179/1eU
Impact strength of cantilever beam notch			ASTM D256
-20℃	49	J/m	ASTM D256
23℃	98	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	75.0	℃	ISO 75-2/B
Vicat Softening Temp
A50	150	℃	ISO 306/A50

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	95		ASTM D785
Tensile modulus
Secant, 23 ℃	1100	MPa	ISO 527-1-2
tensile strength
yield	26.5	MPa	ASTM D638
Yield, 23 ℃	24.0	MPa	ISO 527-2/50
Tensile strain
yield	6.0	%	ASTM D638
Yield, 23 ℃	8.0	%	ISO 527-2/50
Bending modulus
—	1130	MPa	ASTM D790
—	1200	MPa	ISO 178

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.