| About |
|---|
| NANCAR® 1204D is a fluxed blend of 100 parts NBR, 60 parts PVC and 120 parts DEHP. This polymer has sufficient stabilizer for normal aging conditions and can be processed with normal mixing procedures. It has good processability for extrusion, providing smooth surfaces on the resultant product. NANCAR® 1204D is excellent in low hardness application and resistance to abrasion, ozone, oil and fuel. It is suggested to be use in low hardness printing plates and rolls.&& |
| Product Description | |
|---|---|
| Supplier | Nantex |
| Generic | NBR |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Good surface appearance,Good stability,Low Hardness,Good wear resistance,Grease resistance,Ozone resistance |
| Availabilitys | Asia Pacific |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Mooney viscosity | |||
| ML 1+4，100℃ | 29 | MU | ASTM D1646 |
| Acrylonitrile content (Bound) | 33.0 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 68 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 14.3 | MPa | |
| Tensile strain | |||
| fracture | 460 | % | |
| Compression deformation | |||
| 100℃，70 hr | 70 | % |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 100℃，70 hr | -4.0 | % | |
| The rate of change in ultimate elongation in air | |||
| 100℃，70 hr | -24 | % | |
| The rate of change in hardness of a hardness tester in the air | |||
| 100℃，70 hr | 2.0 | ||
| The rate of change in tensile strength | |||
| 100 ℃, 70 hr, in ASTM # 1 oil | 1.0 | % | |
| 100 ℃, 70 hr, in IRM 903 oil | -5.0 | % | |
| Change rate of ultimate elongation | |||
| 100 ℃, 70 hr, in ASTM # 1 oil | -54 | % | |
| 100 ℃, 70 hr, in IRM 903 oil | -42 | % | |
| The rate of change in Shore hardness | |||
| Support A, 100 ℃, 70 hr, in ASTM # 1 oil | 29 | ||
| Support A, 100 ℃, 70 hr, in IRM 903 oil | 24 | ||
| Volume change | |||
| 100 ℃, 70 hr, ASTM standard oil (No.1) | -33 | % | |
| 100 ℃, 70 hr, in IRM 903 oil | -23 | % |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Heat loss | 0.30 | % | ASTM D5688 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Ozone resistance | |||
| 50 pphm X 40℃ X 20% | no crack |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. at 24 hrs, 48 hrs, 72 hrs, 96 hrs, 168 hrs |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |