NEOFLON™ AC-5820

About
NEOFLON Coating Powder is a high performance material made from fluoropolymer resin. Two kinds of NEOFLON Coating Powders, NEOFLON FEP, and PFA Coating Powder, are available. NEOFLON FEP Coating Powder is a fine powder made of tetrafluoroethylene and hexafluoropropylene copolymer and NEOFLON PFA Coating Powder is a fine powder made of tetrafluoroethylene and perfluoroalkylvinylether copolymer. NEOFLON FEP and PFA Coating Powder are low in melt viscosity and excellent in melt fluidity which can give a coating free of pinholes. NEOFLON FEP and PFA are ideal for use as corrosion resistant linings because of their excellent thermal and chemical resistance properties.&&

About

NEOFLON Coating Powder is a high performance material made from fluoropolymer resin. Two kinds of NEOFLON Coating Powders, NEOFLON FEP, and PFA Coating Powder, are available. NEOFLON FEP Coating Powder is a fine powder made of tetrafluoroethylene and hexafluoropropylene copolymer and NEOFLON PFA Coating Powder is a fine powder made of tetrafluoroethylene and perfluoroalkylvinylether copolymer. NEOFLON FEP and PFA Coating Powder are low in melt viscosity and excellent in melt fluidity which can give a coating free of pinholes. NEOFLON FEP and PFA are ideal for use as corrosion resistant linings because of their excellent thermal and chemical resistance properties.&&

Product Description
Supplier	Daikin Fluorochemicals
Generic	PFA
Material Status	Commercial: Active
Features	Weather resistance is good,High purity,Good Electrical Properties,Good liquidity,Low Viscosity,Corrosion Resistant,Solvent resistance,High ESCR
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	2.12 to 2.17	g/cm³	ASTM D792
Apparent density	0.75 to 1.05	g/cm³	JIS K6891
Melt Flow Rate
372℃，5.0kg	5.0 to 7.0	g/10min	ASTM D3307
Particle size	150 to 250	µm

THERMAL	Nominal value	Unit	Test method
Melting temperature	303 to 313	℃	ASTM D3307

Supplementary information	Nominal value	Unit
Adhesive strength
Peel Test	4.0 to 6.0	kN/m
contact angle
Hexadecane	65.0	°
Water	102 to 106	°

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	60		ASTM D2240
tensile strength	19.6 to 31.4	MPa	JIS K6888
Tensile strain
fracture	250 to 350	%	JIS K6888
friction coefficient
With oneself – static	0.050 to 0.080		Internal Method
Taber abraser
CS-17 Wheel	5.00 to 15.0	mg

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.