| About |
|---|
| NORYL GTX GTX4610 resin is a high performance, 10% glass filled blend of PPE/PA that exhibits an excellent balance of non-halogenated flame retardance, dimensional stability, high heat resistance, strength, and flow. The material is available in limited colors for injection molding.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS+PA |
| Material Status | Commercial: Negative |
| Features | Good Rigidity,Good Dimensional Stability,High liquidity,Halogen free,Flame Characteristics,High Heat Resistance,V-1 |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.21 | g/cm³ | ASTM D792 , ISO 1183 |
| Melt Flow Rate | |||
| 300℃，5.0kg | 18 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 300℃，5 kg | 15.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| MD：3.2 mm | 0.88 to 0.94 | % | Internal Method |
| TD：3.2 mm | 0.95 to 1.0 | % | Internal Method |
| Water absorption rate | ISO 62 | ||
| Saturation, 23 ℃ | 3.8 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.50 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 5000 | MPa | ASTM D638 |
| — | 5000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 88.0 | MPa | ASTM D638 |
| yield | 88.0 | MPa | ISO 527-2/5 |
| fracture | 88.0 | MPa | ASTM D638 |
| fracture | 88.0 | MPa | ISO 527-2/5 |
| Tensile strain | ISO 527-2/5 | ||
| yield | 3.0 | % | ISO 527-2/5 |
| fracture | 3.0 | % | ISO 527-2/5 |
| Bending modulus | |||
| 50 mm span | 4600 | MPa | ASTM D790 |
| — | 4600 | MPa | ISO 178 |
| bending strength | |||
| — | 145 | MPa | ISO 178 |
| Yield, 50 mm span | 145 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 5.0 | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | |||
| -30℃ | 65 | J/m | ASTM D256 |
| 23℃ | 80 | J/m | ASTM D256 |
| 23℃ | 5.0 | kJ/m² | ISO 180-1A |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 12.0 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 220 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 64 mm span | 224 | ℃ | ISO 75-2/Bf |
| Vicat Softening Temp | |||
| B50 | 218 | ℃ | ASTM D1525 11 , ISO 306/B50 11 |
| B120 | 220 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | ASTM E831 , ISO 11359-2 | ||
| MD：-40~40℃ | 4.1E-5 | 1/℃ | ASTM E831，ISO 11359-2 |
| TD：-40~40℃ | 7.4E-5 | 1/℃ | ASTM E831，ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | ASTM D149 | ||
| 1.6 mm in air | 23 | kV/mm | ASTM D149 |
| 1.6 mm in oil | 24 | kV/mm | ASTM D149 |
| Compared to the leakage tracing index | PLC 1 | UL 746 | |
| Compared to the leakage tracing index | 425 | V | IEC 60112 |
| High Arc Burning Index (HAI) | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.80 mm | V-1 | UL 94 | |
| 2.00 mm | 5VB 5VA | UL 94 | |
| Glowing wire flammability index | |||
| 2.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | |||
| 1 mm | 825 | ℃ | IEC 60695-2-13 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 93 to 107 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 8.0 | hr | |
| Recommended maximum moisture content | 0.070 | % | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |