| About |
|---|
| PPE+PS blend. 17% Mineral reinforced. Non-brominated, non-chlorinated FR system. UL94 V0 and 5VA listing. UL746C f1. Radiant panel listing. Dielectric strength. Dimensional stability. Suitable for E/E market indoor/outdoor applications including electrical ceiling boxes and smoke detectors.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Halogen free,Flame Characteristics,V-0,5VA |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.25 | g/cm³ | ASTM D792 |
| Melt Flow Rate | ASTM D1238 | ||
| 280℃，5.0kg | 7.6 | g/10min | |
| 300℃，5.0kg | 7.6 | g/10min | |
| Melt Volume Rate | ISO 1133 | ||
| 280℃，5 kg | 6.80 | cm³/10min | |
| 300℃，5 kg | 6.80 | cm³/10min | |
| Shrinkage rate | |||
| MD：3.2 mm | 0.50 to 0.70 | % | Internal Method |
| Weathering resistance | f1 | UL 746C | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 3650 | MPa | ASTM D638 |
| — | 4000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 74.0 | MPa | ASTM D638 |
| yield | 71.7 | MPa | ISO 527-2 |
| fracture | 60.0 | MPa | ASTM D638 |
| fracture | 57.1 | MPa | ISO 527-2 |
| Tensile strain | |||
| yield | 3.8 | % | ASTM D638 |
| yield | 3.7 | % | ISO 527-2 |
| fracture | 8.4 | % | ASTM D638 |
| fracture | 11 | % | ISO 527-2 |
| Bending modulus | |||
| 100 mm span | 3550 | MPa | ASTM D790 |
| 50 mm span | 3670 | MPa | ASTM D790 |
| — | 3800 | MPa | ISO 178 |
| bending strength | |||
| — | 117 | MPa | ISO 178 |
| Yield, 100 mm span | 117 | MPa | ASTM D790 |
| Fracture, 50 mm span | 117 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 10 | kJ/m² | ISO 179/2C |
| Impact strength of cantilever beam notch | |||
| 23℃ | 130 | J/m | ASTM D256 |
| 23℃ | 9.7 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 2200 | J/m | ASTM D4812 |
| Impact strength of cantilever beam notch | |||
| 3.2mm | 810 | J/m | ASTM D256 |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 443 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 117 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 128 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 100 mm span | 126 | ℃ | ISO 75-2/Be |
| 1.8 MPa, unannealed, 3.2 mm | 108 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 116 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 100 mm span | 111 | ℃ | ISO 75-2/Ae |
| Vicat Softening Temp | |||
| B50 | 132 | ℃ | ISO 306 |
| B120 | 136 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | ASTM E831 | ||
| MD：-40~40℃ | 7.1E-5 | 1/℃ | |
| TD：-40~40℃ | 7.8E-5 | 1/℃ | |
| Relative temperature index | 100 | ℃ | UL 746 |
| Electrical performance | 100 | ℃ | UL 746 |
| Impact mechanical performance | 85.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+16 | ohms | ASTM D257 |
| Volume resistivity | 1.2E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.2 mm in oil | 17 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 50 Hz | 2.89 | ||
| 60 Hz | 2.89 | ||
| 1 MHz | 2.70 | ||
| Dissipation factor | ASTM D150 | ||
| 50 Hz | 0.017 | ||
| 60 Hz | 0.017 | ||
| 1 MHz | 4.4E-3 | ||
| Arc resistance | PLC 6 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 2 | UL 746 | |
| High Arc Burning Index (HAI) | PLC 2 | UL 746 | |
| High voltage arc marking rate | |||
| HVTR | PLC 3 | UL 746 | |
| Hot wire ignition | |||
| HWI | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.47 mm | V-0 | ||
| 2.01 mm | 5VA | ||
| Radiation Plate Listing (UL) | YES |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 104 to 110 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 8.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Recommended injection volume | 30 to 70 | % | |
| Barrel rear temperature | 249 to 299 | °C | |
| Barrel middle temperature | 260 to 304 | °C | |
| Barrel front temperature | 271 to 310 | °C | |
| Nozzle temperature | 282 to 310 | °C | |
| Processing (melt) temperature | 282 to 310 | °C | |
| Mold temperature | 76.7 to 104 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 20 to 100 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.20 in/min |
| 3. Type I, 0.20 in/min |
| 4. 0.10 in/min |
| 5. 0.051 in/min |
| 6. 80*10*4 mm |
| 7. 120*10*4 mm |
| 8. Tungsten Electrode |
| 9. Surface |
| 10. UL Tested |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |