| About |
|---|
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Features | Halogen free |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| bending strength | |||
| Yield, 2 mm/min | 87 | MPa | ISO 178 |
| Yield, 2.60 mm/min, 50 mm span | 91 | MPa | ASTM D790 |
| Yield, 1.30 mm/min, 50 mm span | 98 | MPa | ASTM D790 |
| Bending modulus | |||
| 2 mm/mim | 2350 | MPa | ISO 178 |
| 2.60 mm/min, 100 mm span | 2300 | MPa | ASTM D790 |
| 2500 | MPa | ASTM D790 | |
| Rockwell hardness | 120 | ASTM D785 | |
| Taber wear and tear | |||
| CS-17，1 kg | 76 | mg/1000cy | ASTM D1044 |
| tensile strength | |||
| Fracture, Type I, 50 mm/min | 47 | MPa | ASTM D638 |
| Fracture, 50 mm/min | 50 | MPa | ISO 527 |
| Yield, Type I, 50 mm/min | 60 | MPa | ASTM D638 |
| Yield, 50 mm/min | 58 | MPa | ISO 527 |
| Tensile strain | |||
| Fracture, Type I, 50 mm/min | 9 | % | ASTM D638 |
| Fracture, 50 mm/min | 9.2 | % | ISO 527 |
| Yield, Type I, 50 mm/min | 3.6 | % | ASTM D638 |
| Yield, 50 mm/min | 3.2 | % | ISO 527 |
| Tensile modulus | |||
| 50 mm/min | 2580 | MPa | ASTM D638 |
| 1 mm/min | 2600 | MPa | ISO 527 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Notched impact strength of cantilever beam | |||
| 23℃ | 720 | J/m | ASTM D 4812 |
| Impact strength of cantilever beam notch | |||
| 23℃，80*10*4 | 20 | kJ/m² | ISO 180-1A |
| 23℃ | 293 | J/m | ASTM D256 |
| -30℃ | 100 | J/m | ASTM D256 |
| Total energy of instrument impact | |||
| 23℃ | 50 | J | ASTM D 3763 |
| Charpy Notched Impact Strength | |||
| 23℃ | 20 | kJ/m² | ISO 179/2C |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 64 mm span | 82 | ℃ | ISO 75/Af |
| 1.8 MPa, unannealed, 6.4 mm | 86 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 3.2 mm | 78 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 64 mm span | 95 | ℃ | ISO 75/Bf |
| 0.45 MPa, unannealed, 3.2 mm | 95 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| TD：-40~40℃ | 8.1E-05 | 1/℃ | ASTM E831 |
| MD：-40~40℃ | 7.7E-05 | 1/℃ | ASTM E831 |
| Thermal conductivity | 0.24 | W/m-℃ | ASTM C 177 |
| Vicat Softening Temp | 107 | ℃ | ISO 306 |
| B50 | 104 | ℃ | ASTM D1525 |
| Relative temperature index | |||
| Non mechanical impact performance | 95 | ℃ | UL 746B |
| Electrical performance | 95 | ℃ | UL 746B |
| Impact mechanical performance | 80 | ℃ | UL 746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.13 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 24hr | 0.08 | % | ASTM D570 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5-0.7 | % | Internal Method |
| Solution flow rate 280 ℃/5.0 kgf | 20 | g/10 min | ASTM D 1238 |
| Melt Volume Rate | |||
| 280℃，5 kg | 23 | cm³/10min | ISO 1133 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.8E+16 | ohms·cm | ASTM D257 |
| Insulation strength | |||
| In oil | 19.2 | kV/mm | ASTM D 149 |
| Relative permittivity | |||
| 100 kHz | 2.6 | ASTM D150 | |
| 100 Hz | 2.74 | ASTM D150 | |
| Dissipation factors | |||
| 100kHz | 0.0055 | – | ASTM D 150 |
| 100Hz | 0.013 | – | ASTM D 150 |
| Arc resistance | |||
| Tungsten wire | 7 | PLC Code | ASTM D495 |
| Resistance wire ignition | 2 | PLC Code | UL 746A |
| High voltage arc resistance | 4 | PLC Code | UL 746A |
| High current arc ignition | |||
| surface | 2 | PLC Code | UL 746A |
| Compared to the leakage tracing index | 1 | PLC Code | UL 746A |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.01 mm | HB | UL 94 | |
| 1.47 mm | V0 | UL 94 | |
| 2.99 mm | 5VA | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| drying temperature | 75 – 80 | °C | |
| Drying time | 3 – 4 | hrs | |
| Drying time (gradually increasing) | 8 | hrs | |
| Maximum moisture content | 0.02 | % | |
| Melt Temperature | 250 – 275 | °C | |
| Spray nozzle temperature | 250 – 275 | °C | |
| Front temperature | 240 – 275 | °C | |
| Mid section temperature | 225 – 270 | °C | |
| Post stage temperature | 215 – 265 | °C | |
| Mold temperature | 55 – 75 | °C | |
| Back pressure | 0.3 – 0.7 | MPa | |
| Screw speed | 20 – 100 | rpm | |
| Shooting cylinder size | 30 – 70 | % | |
| Depth of exhaust groove | 0.038 – 0.051 | mm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |