| About |
|---|
| NORYL NH5020 Resin is an unreinforced blend of Polyphenylene Ether(PPE) + Polystyrenre resin. The material offers a good balance of heat, flow, hydrolytic stability, and non-halogenated flame retardant. The material is suitable for injection molding and is available in custom colors.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Features | Hydrolysis stability,Good liquidity,Halogen free,Flame Characteristics,Heat Resistance, Good,V-2,V-0,5VA |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.11 | g/cm³ | ASTM D792 |
| Density | 1.11 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 280℃，5.0kg | 9.8 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 280℃，5 kg | 10.1 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.50 to 0.70 | % | Internal Method |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.25 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.050 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2730 | MPa | ASTM D638 |
| Tensile modulus | 3060 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 77.5 | MPa | ISO 527-2/50 |
| fracture | 62.2 | MPa | ASTM D638 |
| yield | 79.2 | MPa | ASTM D638 |
| yield | 80.1 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| fracture | 5.7 | % | ISO 527-2/50 |
| fracture | 15 | % | ASTM D638 |
| yield | 5.0 | % | ASTM D638 |
| yield | 4.8 | % | ISO 527-2/50 |
| Bending modulus | 2980 | MPa | ISO 178 |
| 50 mm span | 3000 | MPa | ASTM D790 |
| bending strength | 126 | MPa | ISO 178 |
| bending strength | |||
| Yield, 50 mm span | 122 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 7.9 | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -30℃ | 59 | J/m | ASTM D256 |
| 23℃ | 91 | J/m | ASTM D256 |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -30℃ | 6.1 | kJ/m² | ISO 180-1A |
| 23℃ | 8.1 | kJ/m² | ISO 180-1A |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 19.3 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 1.8 MPa, unannealed, 64 mm span | 119 | ℃ | ISO 75-2/Af |
| 0.45 MPa, unannealed, 3.2 mm | 122 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 134 | ℃ | ASTM D648 |
| Hot deformation temperature | ASTM D648 | ||
| 1.8 MPa, unannealed, 3.2 mm | 117 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 123 | ℃ | ASTM D648 |
| Vicat Softening Temp | 138 | ℃ | ASTM D1525 10 |
| Vicat Softening Temp | |||
| B50 | 138 | ℃ | ISO 306 |
| B120 | 139 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 125℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | |||
| TD：-40~40℃ | 6.8E-5 | 1/℃ | ISO 11359-2 |
| TD：-40~40℃ | 6.8E-5 | 1/℃ | ASTM E831 |
| MD：-40~40℃ | 6.1E-5 | 1/℃ | ASTM E831 |
| MD：-40~40℃ | 6.1E-5 | 1/℃ | ISO 11359-2 |
| Relative temperature index | |||
| Electrical performance | 110 | ℃ | UL 746 |
| Strength mechanical performance | 110 | ℃ | UL 746 |
| Impact mechanical performance | 105 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| 3.2 mm in oil | 49 | kV/mm | IEC 60243-1 |
| Arc resistance | PLC 6 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 2 | UL 746 | |
| Compared to the leakage tracing index | 2.00 | V | IEC 60112 |
| High Arc Burning Index (HAI) | PLC 0 | UL 746 | |
| High voltage arc ignition resistance index (HVAR) (PLC) | PLC 4 | UL 746 | |
| Hot wire ignition | |||
| HWI | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.40 mm | V-2 | UL 94 | |
| 0.75 mm | V-0 | UL 94 | |
| 2.50 mm | 5VA | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 104 to 110 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 8.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Recommended injection volume | 30 to 70 | % | |
| Barrel rear temperature | 243 to 293 | °C | |
| Barrel middle temperature | 254 to 299 | °C | |
| Barrel front temperature | 266 to 304 | °C | |
| Nozzle temperature | 277 to 304 | °C | |
| Processing (melt) temperature | 277 to 304 | °C | |
| Mold temperature | 71 to 99 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 20 to 100 | rpm | |
| Vent depth | 0.038 to 0.051 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. Type I, 2.0 in/min |
| 4. 0.051 in/min |
| 5. 0.079 in/min |
| 6. at Yield |
| 7. 80*10*4 sp=62mm |
| 8. 80*10*4 mm |
| 9. Rate A (50°C/h), Loading 2 (50 N) |
| 10. Tungsten Electrode |
| 11. Surface |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |