| About |
|---|
| NORYL ENV105 is an impact modified extrusion grade with a Vicat B/120 of 115C according ISO 306.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Features | High impact resistance |
| Availabilitys | Europe |
| Process Methods | Profile extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.10 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 280℃，5 kg | 7.00 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.50 to 0.70 | % | Internal Method |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.15 | % | |
| Equilibrium, 23 ℃, 50% RH | 0.060 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | 20 | kJ/m² | |
| 23℃ | 30 | kJ/m² | |
| Impact strength of cantilever beam notch | |||
| 23℃ | 25 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 100 mm span | 110 | ℃ | ISO 75-2/Be |
| 1.8 MPa, unannealed, 100 mm span | 80.0 | ℃ | ISO 75-2/Ae |
| Vicat Softening Temp | |||
| A50 | 110 | ℃ | ISO 306/A50 |
| B120 | 115 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 73~77℃ | 通过 | ||
| 105℃ | 通过 | ||
| Linear coefficient of thermal expansion | |||
| MD：23~80℃ | 8.0E-5 | 1/℃ | |
| TD：23~80℃ | 1.0E-4 | 1/℃ | |
| Thermal conductivity coefficient | 0.23 | W/m/K | ISO 8302 |
| Relative temperature index | 65.0 | ℃ | UL 746 |
| Electrical performance | 65.0 | ℃ | UL 746 |
| Impact mechanical performance | 65.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 0.8 mm in oil | 33 | kV/mm | |
| 1.6 mm in oil | 26 | kV/mm | |
| 3.2 mm in oil | 16 | kV/mm | |
| Relative permittivity | |||
| 50 Hz | 2.80 | ||
| 60 Hz | 2.80 | ||
| 1 MHz | 2.70 | ||
| Dissipation factor | |||
| 50 Hz | 0.010 | ||
| 60 Hz | 0.010 | ||
| 1 MHz | 3.0E-3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | V-1 | UL 94 | |
| Glowing wire flammability index | |||
| 1.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Extreme oxygen index | 32 | % | ISO 4589-2 |
| M1 flame retardant grade | 1.00 | mm | NF P 92501 |
| M2 flame retardant grade | 2.00 | mm | NF P 92501 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | |||
| H358/30 | 90.0 | MPa | ISO 2039-1 |
| Tensile modulus | 2000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 50.0 | MPa | |
| fracture | 40.0 | MPa | |
| Tensile strain | |||
| yield | 4.0 | % | |
| fracture | 10 | % | |
| Bending modulus | 1700 | MPa | ISO 178 |
| bending strength | 60.0 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| Squeeze description | Nominal value | Unit | Test method |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar |
| 3. 0.079 in/min |
| 4. at Yield |
| 5. 80*10*4 sp=62mm |
| 6. 80*10*4 mm |
| 7. 120*10*4 mm |
| 8. Approximate Maximum |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |