| About |
|---|
| NOVAPOL® PF-Y821-MPR is a Linear Low Density Polyethylene material. It is available in North America for blown film or film extrusion. Important attributes of NOVAPOL® PF-Y821-MPR are: Antiblock Antioxidant Butene Comonomer Food Contact Acceptable Good Stiffness Typical application of NOVAPOL® PF-Y821-MPR: Food Contact Applications&& |
| Product Description | |
|---|---|
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good Rigidity,High anti-blocking,Machinable,Food contact compliance,Inoxidizability,Butylene copolymer |
| Availabilitys | North America |
| Process Methods | Film extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.923 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 0.80 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| Blown film | > 0.50 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 38 | µm | |
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 38 µ m, blow molded film | 190 | MPa | ASTM D882 |
| 1% secant, TD: 38 µ m, blow molded film | 230 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 38 µ m, blow molded film | 10.0 | MPa | ASTM D882 |
| TD, yield, 38 µ m, blow molded film | 10.0 | MPa | ASTM D882 |
| MD, fracture, 38 µ m, blow molded film | 30.0 | MPa | ASTM D882 |
| TD, fracture, 38 µ m, blow molded film | 25.0 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 38 µ m, blow molded film | 660 | % | ASTM D882 |
| TD, fracture, 38 µ m, blow molded film | 730 | % | ASTM D882 |
| Drop hammer impact | |||
| 38 µ m, blow molded film | 140 | g | ASTM D1709-A |
| Elmandorf tear strength | ASTM D1922 | ||
| MD: 38 µ m, blow molded film | 200 | g | ASTM D1922 |
| TD: 38 µ m, blow molded film | 390 | g | ASTM D1922 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 38 µ m, blow molded film | 57 | ASTM D2457 | |
| Haze | |||
| 38 µ m, blow molded film | 11 | % | ASTM D1003 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Low friction puncture | |||
| 38.0 µm | 320 | J/cm | Internal Method |
| Notes |
|---|
| 1. This resin is subject to the specific limitation that it may contact food only at temperatures of 212°F and below (21 CFR 176.170(c) Table 2, conditions of use B-H). |
| 2. Typical properties: these are not to be construed as specifications. |
| 3. F50 |
| 4. Blown Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |