Nycast Nyloil - SOLIAO

About
Only NYLOIL from CAST NYLONS LIMITED offers various grades of self-lubricating Nylon bearing material tailored to meet your specific application. A cast nylon with built-in oil lubrication, NYLOIL provides superior machinability, performance, and durability compared to other plastic and traditional bearing materials. These grades of NYLOIL are available to fit the most demanding applications: original green NYLOIL for most bearing applications; food-grade, Natural NYLOIL-FG for direct contact with food. The incorporation of an oil lubricant package into the nylon matrix provides significant advantages over other bearing materials: Lubrication results in 25% lower coefficient of friction than other grades of nylon Performs in harsh environments where lubrication is difficult, impossible or not desirable (food contact) Works successfully in marine applications. Reduced water absorption promotes higher dimensional stability. Works and machines as easily as brass. Oil will not spin out, dry out, or drain out, even under the harshest operating conditions. During NYLOIL’s manufacturing process, an oil lubricant package is completely dispersed within the cast nylon matrix, making it an integral part of the casting’s structure. NYLOIL-FG is a self lubricating nylon bearing material which meets the provisions of FDA Regulations 21 CFR, Section 177.15 (and others) and USDA 3A Sanitary Standards 20-17 for direct contact with food. This is a particularly useful material where additional lubrication is not desirable because of clean ability, contamination, or other considerations. Dimensional Stability With their higher crystallinity, all NYCAST products exhibit improved dimensional stability compared to their extruded nylon counterparts. But NYLOIL provides even better dimensional stability than regular grades of cast nylon: Its oil droplets fill gaps in the amorphous structure of the polymer, allowing less room for water to be absorbed into these areas. The moisture absorption graph shows that despite a slow absorption rate, NYLOIL stabilizes at approximately 2.5% moisture content – less than half the moisture content of other unfilled nylons.&&

About

Only NYLOIL from CAST NYLONS LIMITED offers various grades of self-lubricating Nylon bearing material tailored to meet your specific application. A cast nylon with built-in oil lubrication, NYLOIL provides superior machinability, performance, and durability compared to other plastic and traditional bearing materials. These grades of NYLOIL are available to fit the most demanding applications: original green NYLOIL for most bearing applications; food-grade, Natural NYLOIL-FG for direct contact with food. The incorporation of an oil lubricant package into the nylon matrix provides significant advantages over other bearing materials: Lubrication results in 25% lower coefficient of friction than other grades of nylon Performs in harsh environments where lubrication is difficult, impossible or not desirable (food contact) Works successfully in marine applications. Reduced water absorption promotes higher dimensional stability. Works and machines as easily as brass. Oil will not spin out, dry out, or drain out, even under the harshest operating conditions. During NYLOIL’s manufacturing process, an oil lubricant package is completely dispersed within the cast nylon matrix, making it an integral part of the casting’s structure. NYLOIL-FG is a self lubricating nylon bearing material which meets the provisions of FDA Regulations 21 CFR, Section 177.15 (and others) and USDA 3A Sanitary Standards 20-17 for direct contact with food. This is a particularly useful material where additional lubrication is not desirable because of clean ability, contamination, or other considerations. Dimensional Stability With their higher crystallinity, all NYCAST products exhibit improved dimensional stability compared to their extruded nylon counterparts. But NYLOIL provides even better dimensional stability than regular grades of cast nylon: Its oil droplets fill gaps in the amorphous structure of the polymer, allowing less room for water to be absorbed into these areas. The moisture absorption graph shows that despite a slow absorption rate, NYLOIL stabilizes at approximately 2.5% moisture content – less than half the moisture content of other unfilled nylons.&&

Product Description
Generic	PA6
Material Status	Commercial: Active
Features	Good Dimensional Stability,Low or no water absorption,Low coefficient of friction,Machinable,Food contact compliance,Self-lubricating,Lubricating,Durability
Availabilitys	North America
Process Methods	casting

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.14 to 1.15	g/cm³	ASTM D792
Water absorption rate			ASTM D570
24hr	0.50 to 0.60	%	ASTM D570
saturated	2.0 to 2.5	%	ASTM D570
PV Limit（Unlubed）	110	MPa

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	75 to 96	J/m	ASTM D256
Tensile impact strength	69.4 to 75.7	kJ/m²	ASTM D1822

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature			ASTM D648
0.45 MPa, unannealed	204 to 221	℃	ASTM D648
1.8 MPa, unannealed	93.3 to 204	℃	ASTM D648
Continuous use temperature	110	℃	ASTM D794
Melting temperature	227 to 238	℃
Linear coefficient of thermal expansion
MD	9.0E-5	1/℃	ASTM D696
Operating temperature
Intermittent	166	℃

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	100 to 115		ASTM D785
Tensile modulus	2590 to 3280	MPa	ASTM D638
tensile strength	65.5 to 75.8	MPa	ASTM D638
Tensile strain
fracture	45 to 55	%	ASTM D638
Bending modulus	2590 to 3280	MPa	ASTM D790
bending strength	96.5 to 110	MPa	ASTM D790
Compression modulus	1900 to 2590	MPa	ASTM D695
compressive strength
10% strain	82.7 to 96.5	MPa	ASTM D695
shear strength	55.2 to 62.1	MPa	ASTM D732
friction coefficient
With oneself – dynamic	0.12		ASTM D1894
Load deformation	0.700 to 0.800	%	ASTM D621
Wear factor
K	4.00

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.