| About |
|---|
| OnFlex™ HT 热塑性弹性体聚合物以氢化苯乙烯嵌段共聚物为基础。该系列聚合物专门提供高温下良好的抗压缩永久变形性和高耐热性。另外，OnFlex™ HT 聚合物符合 EN 681-2 标准，提供极好的力学性能、宽广的硬度范围和良好的加工性。&& |
| Product Description | |
|---|---|
| Supplier | Polyone |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,High Heat Resistance,Ozone resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.00 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 3 seconds, 23 ℃, 6.00 mm, injection molding | 60 | DIN 53505 | |
| IRHD hardness | 70 | ISO 48 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | DIN 53504 | ||
| TD, fracture, 23 ℃, 2 mm | 10.5 | MPa | DIN 53504 |
| MD, fracture, 23 ℃, 2.00 mm | 7.90 | MPa | DIN 53504 |
| Tensile strain | DIN 53504 | ||
| TD, fracture, 23 ℃, 2 mm | 840 | % | DIN 53504 |
| Flow rate, fracture, 23 ℃, 2 mm | 650 | % | DIN 53504 |
| tear strength | 32 | kN/m | ISO 34-1 |
| Compression deformation | ISO 815 | ||
| -10℃，72 hr | 46 | % | ISO 815 |
| 23℃，22 hr | 24 | % | ISO 815 |
| 70℃，22 hr | 33 | % | ISO 815 |
| 100℃，22 hr | 42 | % | ISO 815 |
| 125℃，22 hr | 43 | % | ISO 815 |
| 150℃，22 hr | 65 | % | ISO 815 |
| Stress relaxation | ISO 3384 | ||
| 23℃ | 31 | % | ISO 3384 |
| 23℃ | 13 | % | ISO 3384 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 70℃，168 hr，2.00 mm | -0.50 | % | DIN 53504 |
| Changes in tensile stress during fracture in air | |||
| 70℃，168 hr，2.00 mm | -0.90 | % | DIN 53504 |
| The rate of change of Shore hardness in air | |||
| Shore A, 70 ℃, 168 hr | -3.0 | DIN 53505 | |
| Volume change | ISO 1817 | ||
| 70 ℃, 72 hr, in ASTM # 1 oil | 10 | % | ISO 1817 |
| 70 ℃, 168 hr, in water | 0.20 | % | ISO 1817 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Common material types | 苯乙烯类热塑性弹性体 (TES |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 180 to 220 | °C | |
| Mold temperature | 30 to 60 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |