| About |
|---|
| Orgalloy® RS 60 series is a rigid polyamide 6 alloy. Outstanding properties: easy to process, chemical resistance (no known solvents) and low moisture absorption leading to stability of mechanical, electrical and dimensional properties. Orgalloy® RS 6010 NAT grade: 10% glass fiber, balanced properties between impact resistance, stiffness, density. For injection molding and for extrusion of profiles.&& |
| Product Description | |
|---|---|
| Supplier | Arkema |
| Generic | PA6 Alloy |
| Material Status | Commercial: Active |
| Features | High Heat Resistance,Electroplating,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.12 | g/cm³ | ISO 1183-2 |
| Melt Volume Rate | |||
| 235℃，2.16 kg | 6.00 | cm³/10min | ISO 1133 |
| Water absorption rate | |||
| saturated | 3.0 | % | ISO 62-2 |
| balance | 1.2 | % | ISO 62-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | — | MPa | ISO 527-2 2 |
| tensile strength | |||
| fracture | — | MPa | ISO 527-2 2 |
| Tensile strain | |||
| fracture | — | % | ISO 527-2 2 |
| Tensile Creep Modulus（1 hr） | — | MPa | ISO 899-1 2 |
| Tensile creep modulus | |||
| 1000 hr | — | MPa | ISO 899-1 2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 190 | ℃ | ISO 75-2 2 |
| 0.45 MPa | 210 | ℃ | ISO 75-2 2 |
| Melting temperature | 220 | ℃ | ISO 11357-3 2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | — | ohms | IEC 60093 2 |
| Volume resistivity | — | ohms·m | IEC 60093 2 |
| Dielectric strength | 36 | kV/mm | IEC 60243-1 2 |
| Relative permittivity | |||
| 100 Hz | — | IEC 60250 2 | |
| 1 MHz | — | IEC 60250 2 | |
| Dissipation factor | |||
| 100 Hz | — | IEC 60250 2 | |
| 1 MHz | — | IEC 60250 2 | |
| Compared to the leakage tracing index | |||
| CTI | — | IEC 60112 2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | HB | ISO 1210 2 | |
| Flame retardant level | |||
| 3.20 mm | HB | ISO 1210 2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |