| About |
|---|
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Melt Flow Rate | |||
| 260℃ | 110 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| TD | 1.14 | % | ISO 2577 |
| MD | 1.39 | % | ISO 2577 |
| Shrinkage rate | |||
| 120℃ | 0.26 | % | ISO 2577 |
| 120℃ | 0.29 | % | ISO 2577 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | 140 | MPa | ISO 2039-1 |
| Bending stress at 3.5% strain | |||
| 5mm/min | 95 | % | ISO 178 |
| bending strength | |||
| 5 mm/min | 6 | MPa | ISO 178 |
| Bending modulus | |||
| 2 mm/mim | 2900 | MPa | ISO 178 |
| bending strength | |||
| 5 mm/min | 110 | MPa | ISO 178 |
| Tensile creep modulus | |||
| 1h | 800 | MPa | ISO 899-1 |
| 1000h | 600 | MPa | ISO 899-1 |
| tensile strength | |||
| 5 mm/min | 50 | MPa | ISO 527 |
| Yield stress | |||
| 50mm/min | 80 | MPa | ISO 527 |
| Tensile modulus | |||
| 1 mm/min | 3200 | MPa | ISO 527 |
| Tensile strain | |||
| fracture | |||
| 50 mm/min | 20 | % | ISO 527 |
| 5 mm/min | 35 | % | |
| Yield, 50 mm/min | 4 | % | ISO 527 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | ＜10 | kJ/m² | ISO 180-IA |
| -30℃ | ＜10 | kJ/m² | ISO 180-IA |
| Izod notched impact strength | |||
| 23℃ | NB | kJ/m² | ISO 180-IC |
| -30℃ | 250 | kJ/m² | ISO 180-IC |
| Notch impact strength | |||
| 23℃ | ＜10 | kJ/m² | ISO 179-LeU |
| -30℃ | ＜10 | kJ/m² | ISO 179-LeU |
| Tensile impact strength | |||
| 23℃ | NB | kJ/m² | ISO 179-LeU |
| -30℃ | NB | kJ/m² | ISO 179-LeU |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Total penetration energy | |||
| 23℃ | 150 | N.m | ISO 6603-2 |
| -30℃ | 90 | N.m | ISO 6603-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | |||
| 50N | -200 | ℃ | ISO 306 |
| Glow metal wire test temperature | 750 | ℃ | IES 695-2-1 |
| Relative temperature index | 80 | ℃ | UL 746B |
| Temperature index | |||
| 95 | ℃ | IES-216-1 | |
| 3mm | 85 | ℃ | IES-216-1 |
| 130 | ℃ | ||
| 155 | ℃ | ||
| specific heat | 1.6 | Kj | – |
| Thermal conductivity coefficient | 0.25 | W/m/K | ISO 8302 |
| Linear coefficient of thermal expansion | |||
| 23~55℃ | 1.1 | ×10-4/K | ASTM E831 |
| 23~55℃ | 1.0 | ×10-4/K | ASTM E831 |
| Hot deformation temperature | |||
| 1.8 MPa | -55 | ℃ | ISO 75 |
| Melting temperature | |||
| 10k/min | 222 | ℃ | ISO 3146-C |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | V-2 | UL 94 | |
| 3.00 mm | V-2 | UL 94 | |
| Extreme oxygen index | |||
| Upper surface ignition | 22 | % | ISO 4589 |
| Upper surface ignition | 26 | % | ISO 4589 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |