| About |
|---|
| Polyether block amide Pebax® MV 1041 SA 01 MED resin is a thermoplastic elastomer made of flexible and hydrophilic polyether and rigid polyamide. Hydrophilic Pebax® MV 1074 SA 01 MED resin is suitable for extrusion or coextrusion and offers excellent high moisture absorption properties in wet environments, enhancing lubricity against bodily tissue. Pebax® MV 1074 SA 01 MED resin is also an inherently dissipative polymer and can be dry blended or compounded with a polymer matrix to lower the surface resistivity of the final part. This grade offers the highest quality and it is specially designed to meet the stringent requirements of the medical applications such as minimally invasive devices. Upon request, letters regarding USP Class VI compliance can be provided.&& |
| Product Description | |
|---|---|
| Supplier | Arkema |
| Generic | PA12弹性体 |
| Material Status | Commercial: Active |
| Features | Machinable |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.07 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 1.4 | % | ISO 62 |
| 23℃，24hr | 48 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 40 | ISO 868 | |
| tensile strength | |||
| fracture | 30.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | > 700 | % | ASTM D638 |
| Bending modulus | 80.0 | MPa | ISO 178 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 158 | ℃ | ISO 11357-3 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 3.0E+9 | ohms | IEC 60093 |
| Volume resistivity | 2.5E+9 | ohms·cm | IEC 60093 |
| Charge Decay Time | < 1.0 | sec | MIL B-81705 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.502 | Internal Method |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 65 to 75 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Processing (melt) temperature | 200 to 270 | °C | |
| Mold temperature | 25 to 60 | °C | |
| Drying temperature | 65 to 75 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Melt temperature | 210 to 230 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |