Pebax® MV 1074 SA 01

About
Polyether block amide Pebax® MV 1074 SA 01 is a thermoplastic elastomer made of flexible and hydrophilic polyether and rigid polyamide. Pebax® MV 1074 SA 01 is an inherently dissipative polymer and can be dry blended or compounded with a polymer matrix to lower the surface resistivity of the final part. This hydrophilic grade when extruded into either a thin film or laminated on to a substrate offers excellent permeability to moisture vapor while remaining waterproof. This SA grade is specially designed to food uses.&&

About

Polyether block amide Pebax® MV 1074 SA 01 is a thermoplastic elastomer made of flexible and hydrophilic polyether and rigid polyamide. Pebax® MV 1074 SA 01 is an inherently dissipative polymer and can be dry blended or compounded with a polymer matrix to lower the surface resistivity of the final part. This hydrophilic grade when extruded into either a thin film or laminated on to a substrate offers excellent permeability to moisture vapor while remaining waterproof. This SA grade is specially designed to food uses.&&

Product Description
Supplier	Arkema
Generic	PA12弹性体
Material Status	Commercial: Active
Features	Hydrophilic,Antistatic property
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.07	g/cm³	ISO 1183
Water absorption rate
Equilibrium, 23 ℃, 50% RH	1.4	%	ISO 62
23℃，24hr	48	%	ISO 62

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	40		ISO 868
tensile strength
fracture	30.0	MPa	ISO 527-2
Tensile strain
fracture	> 700	%	ISO 527-2
Bending modulus	80.0	MPa	ISO 178

THERMAL	Nominal value	Unit	Test method
Melting temperature	158	℃	ISO 11357-3

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	3.0E+9	ohms	IEC 60093
Volume resistivity	2.5E+9	ohms·cm	IEC 60093
Charge Decay Time	< 1.0	sec	MIL B-81705

optical performance	Nominal value	Unit	Test method
Refractive index	1.502		Internal Method

Process Conditions
injection	Nominal value	Unit	Test method
Extrusion	Nominal value	Unit	Test method
Drying temperature	65 to 75	°C
Drying time	4.0 to 6.0	hr
Processing (melt) temperature	200 to 270	°C
Mold temperature	25 to 60	°C
Drying temperature	65 to 75	°C
Drying time	4.0 to 6.0	hr
Melt temperature	210 to 230	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.