Pinnacle PP 1355Z

About
55 MELT FLOW HOMOPOLYMER POLYPROPYLENE WITH NUCLEATOR AND ANTISTAT FOR THIN WALL INJECTION MOLDING Pinnacle Polymers Polypropylene 1355Z is made via UNIPOL™ PP technology, which utilizes gas-phase fluidized bed reactors with a high activity catalyst system to ensure uniform physical properties and lot-to-lot consistency. This product is intended for thin-wall injection molded applications including closures, food containers and miscellaneous consumer products applications that require high stiffness. The 1355Z product provides: Superior set-up behavior Excellent color and processing stability Low odor and taste Excellent flow characteristics High stiffness Nucleation and antistat This product, as marketed by Pinnacle Polymers Company, in natural, uncolored pellet form complies with appropriate requirements of CFR Title 21, Part 177, and Subpart B, Section 177.1520 (c) 1.1a entitled “Olefin Polymers” of the Food Additives Amendment of 1958 to the United States Food, Drug and Cosmetic Act of 1938.&&

About

55 MELT FLOW HOMOPOLYMER POLYPROPYLENE WITH NUCLEATOR AND ANTISTAT FOR THIN WALL INJECTION MOLDING Pinnacle Polymers Polypropylene 1355Z is made via UNIPOL™ PP technology, which utilizes gas-phase fluidized bed reactors with a high activity catalyst system to ensure uniform physical properties and lot-to-lot consistency. This product is intended for thin-wall injection molded applications including closures, food containers and miscellaneous consumer products applications that require high stiffness. The 1355Z product provides: Superior set-up behavior Excellent color and processing stability Low odor and taste Excellent flow characteristics High stiffness Nucleation and antistat This product, as marketed by Pinnacle Polymers Company, in natural, uncolored pellet form complies with appropriate requirements of CFR Title 21, Part 177, and Subpart B, Section 177.1520 (c) 1.1a entitled “Olefin Polymers” of the Food Additives Amendment of 1958 to the United States Food, Drug and Cosmetic Act of 1938.&&

Product Description
Generic	PP homopolymerization
Material Status	Commercial: Active
Features	Good Rigidity,Excellent Processability,Good liquidity,Nucleation,Food contact compliance,Good color stability,Low odor,Antistatic property,Homopolymer
Availabilitys	North America,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.900	g/cm³	ASTM D1505
Melt Flow Rate
230℃，2.16kg	55	g/10min	ASTM D1238

MECHANICAL	Nominal value	Unit	Test method
tensile strength
Yield, 3.20 mm, injection molding	39.3	MPa	ASTM D638
Tensile strain
Yield, 3.20 mm, injection molding	8.0	%	ASTM D638
Bending modulus
1% cut, 3.20 mm, injection molded	1930	MPa	ASTM D790-A

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23 ℃, 3.2mm, injection molding	3.00	kJ/m²	ASTM D256
23 ℃, 3.2mm, injection molding	32	J/m	ASTM D256

Notes
1. Typical properties: these are not to be construed as specifications.
2. Type I, 2.0 in/min
3. Type I, 0.050 in/min
4. Type I
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.