| About |
|---|
| Plaskolite Acrylic PL-30是一种聚甲基丙烯酸甲酯-丙烯酸材料,。 该产品在北美洲有供货,加工方式为:挤出或注射成型。 Plaskolite Acrylic PL-30的主要特性有: 阻燃/额定火焰 优良的脱模剂 绝缘 耐候性好 耐冲击 典型应用领域包括: 家庭应用 汽车行业&& |
| Product Description | |
|---|---|
| Generic | PMMA |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good Clarity,Good flexibility,High impact resistance,Good stripping performance,Ultra high molecular weight,Solvent resistance,Heat Stabilized,Insulation,HB |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.19 | g/cm³ | ASTM D792 |
| Melt Flow Rate | 3.0 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.30 to 0.70 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.30 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 21 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 92.2 | ℃ | ASTM D648 |
| Melting temperature | 157 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 5.4E-5 | 1/℃ | ASTM D696 |
| specific heat | 1460 | J/kg/℃ | ASTM C351 |
| Thermal conductivity coefficient | 0.20 | W/m/K | ASTM C177 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | 18 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 60 Hz | 3.70 | ASTM D150 | |
| Dissipation factor | |||
| 60 Hz | 0.050 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.490 | ASTM D542 | |
| Transmittance | 92.0 | % | ASTM D1003 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 95 | ASTM D785 | |
| Tensile modulus | 2960 | MPa | ASTM D638 |
| tensile strength | |||
| yield | 72.4 | MPa | ASTM D638 |
| bending strength | |||
| yield | 110 | MPa | ASTM D790 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |