Plexiglas® Hi-Gloss 8N black 9V022

About
PLEXIGLAS® Hi-Gloss 8N black 9V022 is an amorphous thermoplastic molding compound (PMMA). Typical properties of PLEXIGLAS® molding compounds are: good flow high mechanical strength, surface hardness and abrasion resistance very good weather resistance Special properties of PLEXIGLAS® Hi-Gloss 8N 9V022 are: optimum mechanical properties high heat deflection temperature good flow / melt viscosity. Application: PLEXIGLAS® Hi-Gloss 8N black 9V022 is particularly suitable for injection molding technical components. Owing to its superior brilliance, high-gloss (Class A) black surfaces can be obtained. Examples: add-on automotive body parts&&

About

PLEXIGLAS® Hi-Gloss 8N black 9V022 is an amorphous thermoplastic molding compound (PMMA). Typical properties of PLEXIGLAS® molding compounds are: good flow high mechanical strength, surface hardness and abrasion resistance very good weather resistance Special properties of PLEXIGLAS® Hi-Gloss 8N 9V022 are: optimum mechanical properties high heat deflection temperature good flow / melt viscosity. Application: PLEXIGLAS® Hi-Gloss 8N black 9V022 is particularly suitable for injection molding technical components. Owing to its superior brilliance, high-gloss (Class A) black surfaces can be obtained. Examples: add-on automotive body parts&&

Product Description
Supplier	ROHM
Generic	PMMA
Material Status	Commercial: Active
Features	Good Rigidity,Weather resistance is good,Good surface appearance,Good liquidity,Good Hardness,High Heat Resistance,Good wear resistance,Amorphous
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.19	g/cm³	ISO 1183
Melt Volume Rate
230℃，3.8 kg	3.00	cm³/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	3300	MPa	ISO 527-1-2
tensile strength
fracture	77.0	MPa	ISO 527-2/5
Tensile strain
fracture	5.5	%	ISO 527-2/5

IMPACT	Nominal value	Unit	Test method
Charpy Unnotch Impact strength
23℃	20	kJ/m²	ISO 179/1eU

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	103	℃	ISO 75-2/B
1.8 MPa, unannealed	98.0	℃	ISO 75-2/A
Glass transition temperature	117	℃	ISO 11357-2
Vicat Softening Temp
B50	108	℃	ISO 306
Linear coefficient of thermal expansion
MD：0~50℃	8.0E-5	1/℃	ISO 11359-2

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flammability level
1.6 mm	HB		IEC 60695-11-10, -20

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	< 98	°C
Drying time	2.0 to 3.0	hr
Processing (melt) temperature	220 to 260	°C
Mold temperature	60 to 90	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.