| About |
|---|
| POCAN® B7425 000000 PBT, 20 % glass spheres, injection molding, low tendency to warp, improved surface finish&&POCAN® B7425 000000 PBT, 20 % glass spheres, injection molding, low tendency to warp, improved surface finish&&POCAN® B7425 000000 PBT, 20 % glass spheres, injection molding, low tendency to warp, improved surface finish&& |
| Product Description | |
|---|---|
| Supplier | LANXESS |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Low warping,Good surface appearance |
| Availabilitys | Africa & Middle East ,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.44 | g/cm³ | ISO 1183 |
| Apparent density | 0.90 | g/cm³ | ISO 60 |
| Melt Volume Rate | |||
| 260℃，5 kg | 35.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| TD：120℃，2.0 mm | 0.20 | % | |
| TD：260℃，2.0 mm | 2.1 | % | |
| MD：120℃，2.0 mm | 0.20 | % | |
| MD：260℃，2.0 mm | 2.1 | % | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.40 | % | |
| Equilibrium, 23 ℃, 50% RH | 0.10 | % | |
| Viscosity value | |||
| Reduced viscosity | 130.0 | ml/g | ISO 1628 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | < 10 | kJ/m² | |
| 23℃ | < 10 | kJ/m² | |
| Charpy Unnotch Impact strength | |||
| -30℃ | 25 | kJ/m² | |
| 23℃ | 35 | kJ/m² | |
| Impact strength of cantilever beam notch | |||
| Notched impact strength of cantilever beam | |||
| -30℃ | 20 | kJ/m² | |
| 23℃ | 30 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 170 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 70.0 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| B120 | 190 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 200℃ | 通过 | IEC 60695-10-2 | |
| Melting temperature | 225 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| MD：23~55℃ | 1.0E-4 | 1/℃ | |
| TD：23~55℃ | 1.0E-4 | 1/℃ | |
| Thermal conductivity coefficient | |||
| 23℃ | 0.28 | W/m/K | ISO 8302 |
| Relative temperature index | 130 | ℃ | UL 746 |
| Electrical performance | 130 | ℃ | UL 746 |
| Impact mechanical performance | 125 | ℃ | UL 746 |
| Halving Interval | |||
| Dielectric strength | 11.4 | ℃ | |
| 23 ℃，1 mm | 25 | kV/mm | IEC 60243-1 |
| Tensile impact strength | 7.8 | ℃ | |
| tensile strength | 14.0 | ℃ | |
| Fracture, 23 ℃ | 50.0 | MPa | ISO 527-2/5 |
| Temperature index | |||
| Dielectric strength, 20000 hr | 160 | ℃ | |
| Tensile impact strength, 20000 hr | 130 | ℃ | |
| Tensile strength, 20000 hr | 140 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | |||
| 23℃ | > 1.0E+15 | ohms·cm | IEC 60093 |
| Relative permittivity | |||
| 23℃，100 Hz | 3.80 | ||
| 23℃，1 MHz | 3.60 | ||
| Dissipation factor | |||
| 23℃，1 MHz | 0.017 | IEC 60250 | |
| Compared to the leakage tracing index | |||
| Solution A | 250 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| US FMVSS302 | passed | ISO 3795 | |
| Flame retardant level | |||
| 0.75 mm | HB | ||
| 1.50 mm | HB | ||
| Glowing wire flammability index | |||
| 2.0 mm | 650 | ℃ | IEC 60695-2-12 |
| Extreme oxygen index | 23 | % | ISO 4589-2 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Electrolytic corrosion | |||
| 23℃ | A1 | IEC 60426 | |
| ISO Shortname | ISO 7792-1-PBT, GHMR, 11-030, GB20 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | 160 | MPa | ISO 2039-1 |
| Tensile modulus | |||
| 23℃ | 3300 | MPa | ISO 527-1-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 6.0 | % | ISO 527-2/5 |
| Tensile creep modulus | |||
| 1 hr | 3300 | MPa | |
| 1000 hr | 2700 | MPa | |
| Bending modulus | |||
| 23℃ | 3300 | MPa | ISO 178-A |
| bending strength | |||
| 23℃ | 90.0 | MPa | |
| 3.50% strain, 23 ℃ | 85.0 | MPa | |
| Bending strain | 5.0 | % | ISO 178/A |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – Dehumidifying desiccant | 120 | °C | |
| Drying time – Dehumidifying desiccant | 4.0 to 8.0 | hr | |
| Processing (melt) temperature | 250 to 270 | °C | |
| Mold temperature | 80 to 100 | °C | |
| Residual Moisture Content | 0.0 to 0.020 | % | Karl Fisher |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 60x60x2mm, 4 hr |
| 3. 60x60x2mm, 80°C MT, 600 bar |
| 4. 0.079 in/min |
| 5. 2 mm/min |
| 6. 10°C/min |
| 7. Procedure A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |