| About |
|---|
| Politen® G1GP10 is a Polyester Alloy material filled with glass fiber. It is available in North America. Important attributes of Politen® G1GP10 are: Flame Rated REACH Compliant RoHS Compliant&& |
| Product Description | |
|---|---|
| Generic | 间苯二甲酸聚酯 |
| Material Status | Commercial: Active |
| Features | Good Electrical Properties,Heat Stabilized,HB |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.77 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 24hr，3.18 mm | 0.27 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D638 | ||
| MD，3.18 mm | 82.7 | MPa | ASTM D638 |
| TD，3.18 mm | 66.2 | MPa | ASTM D638 |
| bending strength | ASTM D790 | ||
| 3.18 mm | 170 | MPa | ASTM D790 |
| 3.18 mm | 139 | MPa | ASTM D790 |
| compressive strength | |||
| 3.18 mm | 187 | MPa | ASTM D695 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| TD，3.2mm | 430 | J/m | ASTM D256 |
| Flow rate, 3.18mm | 430 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative temperature index | |||
| Electrical performance, 3.20 mm | 105 | ℃ | UL 746 |
| 3.20 mm | 160 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| 3.18 mm | 11 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 3.18 mm，1 kHz | 4.57 | ASTM D150 | |
| 3.18 mm，1 MHz | 4.41 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 3.18 mm，1 kHz | 7.5E-3 | ASTM D150 | |
| 3.18 mm，1 MHz | 0.015 | ASTM D150 | |
| Arc resistance | |||
| 3.18 mm | 125 | sec | ASTM D495 |
| Compared to the resistance to leakage and marking index | |||
| 3.18 mm | > 500 | V | UL 746 |
| High Arc Burning Index (HAI) (3.18 mm) | 79.0 | UL 746 | |
| High voltage arc marking rate (HVTR) (3.18 mm) | 5.60 | mm/min | UL 746 |
| Hot wire ignition (HWI) (3.18 mm) | 11 | sec | UL 746 |
| breakdown voltage | |||
| 3.18 mm | 65300 | V | ASTM D149 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 3.20 mm | HB | UL 94 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Across Flow, Condition A |
| 3. Flow, Condition A |
| 4. Across Flow |
| 5. Condition A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |