| About |
|---|
| Polymer-E F2201 is a Low Density Polyethylene product. It is available in Asia Pacific. Applications of Polymer-E F2201 include film and hose/tubing. Characteristics include: Antiblock Good Aesthetics Slip&& |
| Product Description | |
|---|---|
| Supplier | APC |
| Generic | LDPE |
| Material Status | Commercial: Negative |
| Features | Optical performance |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.923 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 2.3 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 32 µ m, blow molded film | 193 | MPa | ASTM D882 |
| 1% secant, TD: 32 µ m, blow molded film | 221 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, fracture, 32 µ m, blow molded film | 23.5 | MPa | ASTM D882 |
| TD, fracture, 32 µ m, blow molded film | 17.7 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 32 µ m, blow molded film | 320 | % | ASTM D882 |
| TD, fracture, 32 µ m, blow molded film | 540 | % | ASTM D882 |
| Drop hammer impact | |||
| 32 µ m, blow molded film | 90 | g | ASTM D1709 |
| tear strength | ASTM D1922 | ||
| MD，31.8 µm | 88.3 | kN/m | ASTM D1922 |
| TD，31.8 µm | 68.6 | kN/m | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 49.0 | ℃ | ASTM D648 |
| Embrittlement temperature | < -70.0 | ℃ | ASTM D746 |
| Vicat Softening Temp | 97.0 | ℃ | ASTM D1525 |
| Melting temperature | 110 | ℃ | Internal Method |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60 °, 31.8 µ m, blow molded film | 120 | ASTM D523 | |
| Haze | |||
| 31.8 µ m, blow molded film | 5.0 | % | ASTM D1003 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 52 | ASTM D2240 | |
| friction coefficient | < 0.11 | ASTM D1894 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Blown Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |